119931
16
Zoom out
Zoom in
Previous page
1/119
Next page
English - 3
For all work with the machine, the auxiliary
handle must be mounted.
Hold the power tool only by the insulated
gripping surfaces, when performing an op-
eration where the cutting tool may run into
hidden wiring or its own cord.
Contact with a live wire will make exposed
metal parts of the tool live and shock the op-
erator.
Use appropriate detectors to determine if
utility lines are hidden in the work area or
call the local utility company for assist-
ance.
Contact with electric lines can lead to fire and
electric shock. Damaging a gas line can lead
to explosion. Penetrating a water line causes
property damage or may cause an electric
shock.
For work with grinding or cutting discs, the pro-
tection guard 7 must be mounted. For work
with the rubber sanding plate 21 or with the
cup brush 24/disc brush/flap disc, the hand
guard 19 (accessory) is to be mounted.
Use dust extraction when working with stone.
The vacuum cleaner must be approved for ma-
sonry dust. When cutting stone, use the cutting
guide.
Do not work with materials containing asbes-
tos.
Use only grinding tools with a permissible
speed at least as high as the no-load speed of
the machine.
Check grinding tools before use. The grinding
tool must be properly mounted and turn freely.
Perform a test run for at least 30 seconds with-
out load. Do not use damaged, out-of-round or
vibrating grinding tools.
Protect the grinding tool from impact, shock
and grease.
Apply the machine to the workpiece only when
switched on.
Keep hands away from rotating grinding tools.
Pay attention to the direction of rotation. Al-
ways hold the machine so that sparks and
grinding dust fly away from the body.
When grinding metal, flying sparks are pro-
duced. Take care that no persons are endan-
gered. Due to danger of fire, no combustible
materials should be located in the vicinity
(spark flight zone).
Be careful when cutting grooves, e. g. in struc-
tural walls: See Information on Structures.
Blocking the cutting disc leads to jerking reac-
tion forces on the machine. In this case switch
off the machine immediately.
Pay attention to the dimensions of the grinding
disc. The mounting hole diameter must fit the
mounting flange 10 without play. Do not use
reducers or adapters.
Never use cutting discs for rough grinding. Do
not exert any lateral pressure on the cutting
discs.
Observe the manufacturers instructions for
mounting and using grinding tools.
Caution! The grinding tool runs on after the
machine is switched off.
Do not clamp the machine in a vice.
Never allow children to use the machine.
Bosch is only able to ensure perfect operation
of the machine if the original accessories in-
tended for it are used.
Before any work on the machine itself, pull
the mains plug.
For work with grinding or cutting discs, the
protection guard 7 must be mounted.
Protection Guard with Locking Screw
The coded projection 15 on the protection
guard 7 ensures that only a guard that fits the
machine type can be mounted.
Loosen the clamping screw 14, if necessary.
Place the protection guard 7 with coded projec-
tion 15 into the coded groove on the spindle col-
lar of the machine head and rotate to the required
position (working position).
The closed side of the protection guard 7
must always point to the operator.
Tighten clamping screw 14.
Mounting the
Protective Devices
17 • 1 609 929 F55 • TMS • 18.12.03
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 24-180-230 (J) BV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 24-180-230 (J) BV in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info