786154
13
Zoom out
Zoom in
Previous page
1/171
Next page
English | 13
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Battery Charging
uUse only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
uDo not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the battery
To remove the battery (7), press the release buttons (6) and
pull the battery back and out of the power tool. Do not use
force to do this.
Changing the Tool (see figure A)
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Pull the depth stop (4) off towards you. Pull the screwdriver
bit (1) out. If required, the universal bit holder (11) can also
be pulled out and replaced.
An auxiliary tool can be used to remove the screwdriver bit
or universal bit holder.
After changing the tool, reattach the depth stop (4).
Operation
Starting Operation
Inserting the Battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (5) to the middle position
to avoid unintentionally switching it on. Insert the charged
battery (7) into the handle until you feel it engage and it is
flush with the handle.
Setting the Rotational Direction
The rotational direction switch (5) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (10) is being pressed.
Right rotation: Slide the rotational direction switch
(5) all the way into position on both sides.
Left rotation: Slide the rotational direction switch (5)
all the way into position on both sides.
Switching on/off
To start the power tool, press and hold the on/off switch
(10).
The LED (9) lights up when the on/off switch (10) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (10).
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (10) to varying extents.
A light pressure on the on/off switch (10) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Adjusting the screw-in depth (see figure B)
The depth to which the screw head is screwed into the work-
piece can be preset by turning the adjusting sleeve (3) to 8
engaging steps for each rotation. Each step corresponds to a
0.25 mm change in the screw-in depth.
Turning the adjusting sleeve (3) clockwise increases the
screw-in depth; turning it anticlockwise decreases the
screw-in depth.
The best way to determine the setting you require is to drive
in some test screws.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted battery temperature range, the power output is
reduced or the power tool is switched off. The power tool
will not run at full power output again until the permitted bat-
tery temperature has been reached.
Practical advice
uOnly apply the power tool to the screw when the tool
is switched off. Rotating application tools can slip off.
Place the screw against the screwdriver bit(1). The screw
will be held in place by the magnetic retention force of the
universal bit holder(11). Forcefully press the tip of the
screw against the material you wish to screw until the screw
depth stop(4) rests on the workpiece.
Switch the power tool on. The screw is screwed into the
workpiece until it reaches the set screw depth. The drive is
Bosch Power Tools 1 609 92A 7PT | (02.05.2022)
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GTB 12V-11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GTB 12V-11 in the language / languages: All languages as an attachment in your email.

The manual is 3.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info