786281

Bosch GSS 18V-10 Manual

16
Zoom out
Zoom in
Previous page
1/205
Next page
16 | English
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
uAvoid dust accumulation at the workplace. Dust can
easily ignite.
Self-generated dust extraction with dust box (see figures
E1–E4)
Place the dust box (1) onto the extraction outlet (15) until it
clicks into place.
To empty the dust box (1), pull the dust box downwards.
Before opening the dust box (1), knock the dust box against
a firm surface as shown in the figure to loosen the dust from
the filter element.
Take hold of the dust box (1) by the recessed grip, fold the
filter element (16) upwards out of the way and empty the
dust box. Use a soft brush to clean the flaps of the filter ele-
ment (16).
External dust extraction (see figure F)
Attach the dust extraction adapter (17) to the extraction
outlet (15). Make sure that the locking levers of the extrac-
tion adapter lock into place. A dust extraction hose with a
diameter of 19mm can be connected to the dust extraction
adapter (17).
You will find an overview of connecting to various dust ex-
tractors at the end of these operating instructions.
To remove the dust extraction adapter (17), press the rear
locking levers together and take off the extraction adapter.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Operation
Starting Operation
Switching On/Off
uMake sure that you are able to press the On/Off switch
without releasing the handle.
To switch on the power tool, tilt the on/off switch (8) to-
ward the right to the “I” position.
To switch off the power tool, tilt the on/off switch (8) to-
ward the left to the “O” position.
Battery charge indicator
The three green LEDs of the battery charge indicator (10)
show the charging status of the battery (11). For safety
reasons, it is only possible to check the charging status when
the power tool is at a standstill.
Press the button (9) to display the charging status. This is
also possible when the battery (11) is removed.
LEDs Capacity
3× continuous green light ≥66%
2× continuous green light ≥33%
1× continuous green light <33%
1× flashing green light Reserve
If no LED lights up after pressing the button (9), then the
battery is defective and must be replaced.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
Practical advice
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
uAlways wait until the power tool has come to a com-
plete stop before placing it down.
The material removal rate when sanding is primarily determ-
ined by the choice of sanding sheet.
Only immaculate sanding sheets achieve good sanding per-
formance and make the power tool last longer.
Be sure to apply consistent contact pressure in order to in-
crease the lifetime of the sanding sheets.
Excessively increasing the contact pressure will not lead to
increased sanding performance, rather it will cause more
severe wear of the power tool and of the sanding sheet.
Do not use a sanding sheet for other materials after it has
been used to work on metal.
Use only original Bosch-sanding accessories.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50°C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
1 609 92A 7TF | (24.06.2022) Bosch Power Tools
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSS 18V-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSS 18V-10 in the language / languages: All languages as an attachment in your email.

The manual is 4.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info