Manual Bosch GSS 18V-10 (page 15 of 205) (All languages)

786281

Zoom out

Zoom in

1/205

English | 15

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Charge the battery

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

To remove the battery (11), press the release button (12)

and pull the battery sideways out of the power tool. Do not

use force to do this.

Follow the instructions on correct disposal.

Fitting the base plate (see figure A)

Unscrew the four screws (14) completely. Fit a suitable base

plate and retighten the screws.

Changing the sanding plate (see figure A)

If necessary, the sanding plate (3) can be replaced.

Unscrew the four screws (14) completely and remove the

sanding plate (3). Fit the new sanding plate (3) and

retighten the screws.

Changing the sanding sheet

Remove dirt and dust from the sanding plate (3), e.g. with a

brush, before attaching a new sanding sheet.

To ensure optimum dust extraction, make sure that the

punched holes in the sanding sheet are aligned with the

drilled holes in the sanding plate.

Sanding sheets without hook-and-loop backing (see

figures B–D)

Unlock both sanding-sheet clamps (4) and swivel them

downwards.

Insert the sanding sheet (6) under the rear clamping

bracket (2). Ensure that the sanding sheet (6) is not too

short and that it is correctly clamped. Swivel the sand-

ing-sheet clamp (4) back into the starting position and

lock it in place.

Position the sanding paper so that it fits tightly around

the sanding plate (3). Clamp the front part of the sand-

ing sheet under the front clamping bracket (7). Ensure

that the sanding sheet (6) is not too short and that it is

correctly clamped. Swivel the sanding-sheet clamp (4)

back into the starting position and lock it in place.

Unperforated sanding sheets, e.g. from rolls or bulk stock

sold by the metre, can be perforated using the punch (19)

for the purpose of dust extraction. To do this, fit the sanding

sheet on the power tool and push the tool down onto the

punch (see figureG).

To remove the sanding sheet (6), unlock both sanding-sheet

clamps (4) and pull the sanding sheet out of its bracket.

Selecting a sanding sheet

Different sanding sheets are available, depending on the ma-

terial you are working with and the required surface removal

rate:

Grit

For processing all wood and wood-based ma-

terials

40–180

For pre-sanding, e.g. of rough and un-

even beams and boards Coarse 40

For surface sanding and levelling of

slight irregularities Medium 80, 120

For finish-sanding and fine sanding of

hardwoods Fine 180

For processing paint and lacquer layers or

primers such as fillers and bodyfillers

40–180

For sanding down paint Coarse 40

For sanding undercoats Medium 80, 120

For final sanding of primers prior to

painting Fine 180

For any finishing work, such as polishing (metal and stone in

particular), use fleece/polishing felt.

Different types of fleece and polishing felts should be used

depending on the surface finish required on the workpiece.

Bosch Power Tools 1 609 92A 7TF | (24.06.2022)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSS 18V-10 in the language / languages: All languages as an attachment in your email.

The manual is 4.38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GSS 18V-10 Manual

Product: