786087
12
Zoom out
Zoom in
Previous page
1/20
Next page
12 | English
used, the application tool will be stopped when the screw is
driven flush into the material or once the set torque has been
reached. In position the overload clutch is deactivated,
e.g. for drilling.
When unscrewing screws, you can select a higher setting or
set the tool to the symbol.
Mechanical gear selection
uOnly operate the gear selector (6) when the power
tool is not in use.
You can preselect two speed ranges with the gear selector
(6).
Gear I:
Low speed range; for screwdriving or working with a large
drilling diameter.
Gear II:
High speed range; for working with a small drilling diameter.
Setting the Operating Mode
Drilling
GSR
Set the torque presetting ring (4) to the
"drilling" symbol.
GSB
Set the operating mode presetting ring (5) to
the "drilling" symbol.
Screwdriving
GSR
Set the torque presetting ring (4) to the re-
quired torque.
GSB
Set the operating mode presetting ring (5) to
the "screwdriving" symbol.
Set the torque presetting ring(4) to the re-
quired torque.
Impact drilling (GSB)
Set the operating mode presetting ring (5) to
the "impact drilling" symbol.
Adjusting the Speed/Impact Rate
You can adjust the speed/impact rate of the power tool when
it is on by pressing in the on/off switch (10) to varying ex-
tents.
Applying light pressure to the on/off switch (10) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Switching on/off
To start the power tool, press and hold the on/off switch
(10).
To switch off the power tool, release the on/off switch (10).
Fully automatic spindle lock (Auto-Lock)
The drill spindle, and therefore the tool holder (1), are
locked when the on/off switch (10) is not pressed.
This enables screws to be screwed in even when the battery
(9) is empty and allows the power tool to be used as a
screwdriver.
Battery charge-control indicator
When the on/off switch (10) is pressed in halfway or com-
pletely, the battery charge-control indicator (11) indicates
the charge condition of the battery for several seconds. The
indicator consists of three green LEDs.
The three LEDs of the battery charge-control indicator (11)
and the lamp (12) flash urgently when the temperature of
the battery falls or rises outside the operating temperature
range of –20 to +50°C.
LED Capacity
Continuous light 3 x green ≥ 76%
Continuous light 2 x green 51–75%
Continuous light 1 x green 26–50%
Slowly flashing light 1 x green ≤ 25%
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If there is an extreme overload, the power tool
switches off until the optimal operating temperature range is
reached again.
This status is indicated by the three battery charge indicator
(11) LEDs flashing in a chase sequence. The LEDs turn off if
the power tool has reached the optimum operating temper-
ature again.
Practical advice
uOnly apply the power tool to the screw/nut when the
tool is switched off. Rotating tool inserts can slip off.
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed for ap-
proximately three minutes without load to cool it down.
When drilling into metal, only use sharpened HSS drills (HSS
= high-speed steel) which are in perfect condition. The
Bosch accessory range guarantees appropriate quality.
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.
Belt clip (see figure E)
You can use the belt clip (16) to hang the power tool on a
belt, for example. You then have both hands free and the
power tool is always within easy reach.
Bit holder (see figure F)
You can place screwdriver bits in the bit holder (17) for stor-
age.
Colour clip (see figure G)
The colour clip (18) can only be used if the belt clip (16) or
bit holder are not fitted.
1 609 92A 6G9 | (17.06.2021) Bosch Power Tools
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSR 10.8V-35 HX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSR 10.8V-35 HX in the language / languages: English as an attachment in your email.

The manual is 2.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info