786087
11
Zoom out
Zoom in
Previous page
1/20
Next page
English | 11
Cordless Drill/Driver GSB 10.8V-35 GSR 10.8V-35 GSR 10.8V-35 HX
Recommended chargers GAL 12...
GAX 18...
GAL 12...
GAX 18...
GAL 12...
GAX 18...
A) Measured at 20−25°C with rechargeable batteryGBA 10.8V 6.0Ah.
B) Measured withGBA 10.8V 2.0Ah andGBA 10.8V 6.0Ah
Assembly
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
uUse only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
uDo not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the battery (see figureA)
To remove the battery (9), press both release buttons (8)
and pull the battery downwards out of the power tool. Do
not use force to do this.
Changing the tool
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting the application tool: GSR 10.8V-35 HX (see
figureC)
Pull the locking sleeve (3) back, guide the application tool
into the tool holder (1) as far as it will go and release the
locking sleeve (3) to lock the application tool.
Please note that the locking interface is optimized for
the most commonly used application tool dimension in
the individual country of use.
Inserting the application tool: GSB 10.8V-35/GSR
10.8V-35 (see figureB)
Open the keyless chuck (2) by turning it in the direction of
rotation until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation . This will automatically lock the
drill chuck.
The lock will disengage again if you turn the sleeve in the op-
posite direction to remove the tool.
Removing the application tool: GSR 10.8V-35 HX
Pull the locking sleeve (3) back and pull the application tool
out of the holder (1).
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
Provide for good ventilation of the working place.
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
uAvoid dust accumulation at the workplace. Dust can
easily ignite.
Operation
Starting Operation
Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (7) to the middle position
to avoid unintentionally switching it on. Insert the charged
battery (9) into the handle until you feel it engage and it is
flush with the handle.
Setting the rotational direction (see figureD)
The rotational direction switch (7) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (10) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (7) through to the left stop.
Left rotation: To loosen and unscrew screws, press the ro-
tational direction switch (7) through to the right stop.
Preselecting the Torque
The torque presetting ring (4) can be used to preselect the
required torque in 20 stages. When the correct setting is
Bosch Power Tools 1 609 92A 6G9 | (17.06.2021)
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSR 10.8V-35 HX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSR 10.8V-35 HX in the language / languages: English as an attachment in your email.

The manual is 2.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info