544367
16
Zoom out
Zoom in
Previous page
1/158
Next page
1 609 929 Y30 | (16.8.12) Bosch Power Tools
16 | English
Correction of Malfunctions
Accessories
For more information on the complete quality accessories
program, please refer to the Internet under
www.bosch-pt.com or contact your specialist shop.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions con-
cerning maintenance and repair of your product as well as
spare parts. Exploded views and information on spare
parts can also be found under:
www.bosch-pt.com
Our customer service representatives can answer your
questions concerning possible applications and adjust-
ment of products and accessories.
Problem Cause Corrective Measure
The pneumatic tool is ready for operation but no nails are dis-
charged.
A nail is jammed in the shot duct. Clear the jam.
(See “Clearing Jams”, page 15)
The magazine slider is 7 defective. Clean and lubricate the magazine slider 7 as required
and make sure that the magazine 8 is not dirty/soiled.
The spring of the magazine slider is too week or defective. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The fasteners being used are not permitted. Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble “Technical Data” may be used.
The magazine 8 is empty. Refill the magazine.
(See “Loading the Magazine”, page 14)
The nails are discharged very slowly and with too little pres-
sure.
The rated pressure of the compressed-air supply is too low. Increase the compressed-air supply. 8 bar may not be
exceeded.
The driver blade is damaged. Use only the lubricants recommended by Bosch.
(See “Lubricating the Pneumatic Tool”, page 15)
The sealing ring of the piston is worn or damaged. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The buffer is worn. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The length and diameter of supply-air hose 13 do not corre-
spond with the data of this pneumatic tool.
Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 13)
The supply-air hose 13 is bent/creased. Correct the bend/crease in the supply-air hose.
The nails are driven in too deep.
The rated pressure of the compressed-air supply is too high. Reduce the compressed-air supply. 5bar may not be
fallen below.
The depth stop is set too deep. Adjust the depth stop to the desired depth.
(See “Adjusting the Depth Stop”, page 15)
The buffer is worn. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The nails are not driven in deep enough.
The rated pressure of the compressed-air supply is too low. Increase the compressed-air supply. 8 bar may not be
exceeded.
The depth stop is set too high. Adjust the depth stop to the desired depth.
(See “Adjusting the Depth Stop”, page 15)
The length and diameter of supply-air hose 13 do not corre-
spond with the data of this pneumatic tool.
Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 13)
The supply-air hose 13 is bent/creased. Correct the bend/crease in the supply-air hose.
The pneumatic tool skips nails or has a too large cycle feed.
The fasteners being used are not permitted. Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble “Technical Data” may be used.
The magazine 8 is not operating correctly. Clean and lubricate the magazine slider 7 as required
and make sure that the magazine 8 is not dirty/soiled.
The spring of the magazine slider is too week or defective. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
The sealing ring of the piston is worn or damaged. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
Frequent jamming of nails in the shot duct.
The fasteners being used are not permitted. Use only original accessories.
Only the fasteners (nails, staples, etc.) specified in ta-
ble “Technical Data” may be used.
Contact an authorised service agent for Bosch power
tools.
The driven nails are bent.
The driver blade is damaged. Contact an authorised service agent for Bosch power
tools.
Have the component replaced there.
Contrary to working with normal operating speed, the nails
are not driven in deep enough at higher operating speed.
The interior diameter of the supply-air hose is too low. Use a supply-air hose with the correct dimensions.
(See “Technical Data”, page 13)
The compressor is not suitable for fast operating speeds. Use a compressor that is sufficiently dimensioned for
the number of connected pneumatic tools and the op-
erating speed.
OBJ_BUCH-1037-004.book Page 16 Thursday, August 16, 2012 4:34 PM
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSN 90-34 DK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSN 90-34 DK in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 14,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info