Manual Bosch GSL 2 (page 16 of 184) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544278

Zoom out

Zoom in

1/184

16 | English

1 618 C00 75G | (10.12.12) Bosch Power Tools

After switching off automatically, switch the measuring tool

off via On/Off switch 8 and then on again, if required.

GSL 2 Set: After switching off automatically, the measuring

tool can be switched on again by pressing any button on the

remote control.

 Do not leave the switched on measuring tool unattend-

ed and switch the measuring tool off after use. Other

persons could be blinded by the laser beam.

When exceeding the maximum permitted operating tempera-

ture of 50 °C, the measuring tool switches off to protect the

laser diode. After cooling down, the measuring tool is ready

for operation and can be switched on again.

Operation with battery pack: The “Electronic Cell Protec-

tion (ECP)” protects the lithium ion battery pack against deep

discharging. When the battery pack is discharged, the meas-

uring tool is switched off by a protective circuit.

When the measuring tool switches off automatically due to a

discharged battery pack, switch the measuring tool off with

the On/Off switch 8. Charge the battery pack before switch-

ing the measuring tool on again. Otherwise, the battery pack

could become damaged.

Allowing the Measuring Tool to Level In

After switching on, the levelling function automatically com-

pensates irregularities within the self-levelling range of ±4°.

The levelling is finished as soon as the laser beams do not

move any more.

If the automatic levelling function is not possible, e.g. be-

cause the surface on which the measuring tool stands devi-

ates by more than 4° from the horizontal plane, the laser

beams flash.

Set up the measuring tool in level position and wait for the

self-levelling to take place. As soon as the measuring tool is

within the self-levelling range of ±4° , the laser beams light up

continuously.

In case of ground vibrations or position changes during oper-

ation, the measuring tool is automatically levelled in again,

yet, possibly to a different height when larger position chang-

es are the case. Upon re-levelling, check if the two laser

beams are aligned at the reference point (see “Aligning the

Height of the Measuring Tool”, page 16) in order to avoid ver-

tical errors.

Aligning the Height of the Measuring Tool

The measuring tool generates two laser beams that can be

seen on the floor surface in front of the measuring tool for dis-

tances beyond 50 cm. The beams must be brought into align-

ment at this reference point, where they can initially be seen

on the floor surface. For this, turn the thumbwheel for height

adjustment 9 clockwise or anticlockwise, until both laser

beams overlap at the reference point and only one beam can

be seen.

When the two laser beams cannot be aligned by turning the

thumbwheel, the position of the measuring tool is significant-

ly above or below the floor surface. Position the measuring

tool at a different location on the floor surface with less height

deviation and align the laser beams there.

Starting Operation of the Remote Control

(GSL 2 Set)

 Protect the remote control against moisture and direct

sunlight.

 Do not subject the remote control to extreme tempera-

tures or variations in temperature. As an example, do

not leave it in vehicles for longer periods. In case of large

variations in temperature, allow the remote control to ad-

just to the ambient temperature before putting it into oper-

ation.

The remote control remains ready for operation as long as a

battery with sufficient voltage is inserted.

The signals of the remote control should reach the reception

lens 4 directly from the front and inclined from above. When

the remote control cannot be pointed directly against a recep-

tion lens, the working range is reduced. By reflecting the sig-

nal (e.g. against walls), the working range can be improved,

even for indirect signals.

Switching the measuring tool on via the remote control after

automatic shut-off of the measuring tool is only possible when

the On/Off switch 8 is still in the “On” position. Switching the

measuring tool off with the remote control is not possible.

Measuring Procedure

Manual Rotation (GSL 2)

Rotate the upper part of the measuring tool to the location

that you want to check. After rotating, wait until the measur-

ing tool has levelled in again and the laser beams no longer

move. Then, check if the laser beams run opaque.

Automatic Rotation (GSL 2 Set)

To check the surface, rotate the upper part of the measuring

tool with the remote control. Manual rotation is not possible.

The following rotation modes are available:

Press button 19 to start fast, continuous rotation in

clockwise direction. Pressing button 19 again ends

the rotation.

Press button 14 to start fast, continuous rotation in

anticlockwise direction. Pressing button 14 again

ends the rotation.

Press button 18 to start slow, continuous rotation in

clockwise direction. Pressing button 18 again ends

the rotation.

Press button 15 to start slow, continuous rotation in

anticlockwise direction. Pressing button 15 again

ends the rotation.

Press button 17 for a single, brief rotation step in

clockwise direction. For each further individual

movement, press button 17 again.

Press button 16 for a single, brief rotation step in

anticlockwise direction. For each further individual

movement, press button 16 again.

OBJ_BUCH-1545-005.book Page 16 Monday, December 10, 2012 11:06 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSL 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GSL 2 Manual

Product: