544372

Bosch GSK 64-34 Manual

17
Zoom out
Zoom in
Previous page
1/218
Next page
English | 17
Bosch Power Tools 1 609 929 X30 | (22.3.11)
Noise/Vibration Information
Measured noise values determined according to EN 12549.
Typically the A-weighted noise levels of the pneumatic tool are: Sound
pressure level 102 dB(A); sound power level 115 dB(A). Uncertainty
K=2dB.
Wear hearing protection!
Overall vibrational values determined according to EN ISO 20643:
Vibrational emission value a
h
<2.5m/s
2
. Uncertainty K =1.5 m/s
2
.
Declaration of Conformity
We declare under our sole responsibility that the product described un-
der “Technical data” is in conformity with the following standards or
standardization documents: EN 792 according to the provisions of the di-
rectives 2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 22.03.2011
Assembly
Connecting the Air Supply (see figure A)
Make sure that the pressure of the compressed-air system is below the
maximum permitted rated pressure of the pneumatic tool. Firstly, set the
air pressure to the lower value of the recommended rated pressure (see
“Technical Data”).
When in doubt, check the pressure at the air inlet with a pressure gauge
with the pneumatic tool switched on.
For maximum performance, the values for the supply-air hose 15 (con-
nection thread, maximum operating pressure, inner hose diameter, max-
imum hose length; see “Technical Data”) must be observed.
The compressed air supplied should be free of foreign material and mois-
ture to protect the tool from damage, contamination, and the formation of
rust.
All fittings, connecting lines and hoses must be dimensioned for the pres-
sure and the required air volume.
Avoid restrictions in the air supply, e.g., from pinching, kinking, or
stretching!
Connecting the Air Supply to the Pneumatic Tool
– Empty the magazine 10.
(See “Emptying the Magazine”, page 18)
For the following worksteps, a fastener can be discharged when interi-
or parts of the pneumatic tool are not in the starting position due to re-
pairs, maintenance or transport.
– Connect the air connector 8 with a supply-air hose 15 equipped with an
air-connection coupling 14.
– Check the proper function by placing the outlet 13 or the rubber work-
piece protector 1 of the pneumatic tool onto a piece of scrap wood or
wood material, and discharging once or twice.
Loading the Magazine (see figures B1–B4)
Disconnect the air supply before making any adjust-
ments, changing accessories, or placing the pneumatic
tool aside. This safety measure prevents accidental start-
ing of the pneumatic tool.
fUse only original Bosch accessories (see “Technical Data”). The
precision parts of the pneumatic tool such as the magazine, the outlet
and the shot duct are matched to Bosch staples, nails and brads. Other
manufacturers use other steel qualities and sizes.
Using fasteners not permitted, can damage the pneumatic tool and
cause injuries.
While loading the magazine, hold the pneumatic tool in such a manner
that the outlet 13 is not pointed at your own body or at other persons.
– Clean and lubricate the magazine slider 11 as required and make sure
that the magazine 10 is not dirty/soiled.
– Insert a fitting nail strip 16 in the T-slot at the end of the magazine 10.
When doing this, the nail tips must be inserted first.
– Push the nail strip in the magazine toward the front until the last nail is
positioned in front of the magazine spring 17.
Note: A lock function of the magazine slider prevents the pneumatic tool
from being started with an empty magazine. The discharge lock-off can-
not be pressed in and blank firing is thus prevented.
– Press the pretensioned nail pusher 18 against the magazine slider 11
and at the same time, pull the magazine slider completely to the end of
the magazine 10.
Note: The magazine slider must slide back with only low force (finger-
pressure). A tight-running magazine slider causes the nails to be driven in
at an incorrect angle.
– With the nail pusher 18 pressed, carefully guide the magazine slider 11
toward the front until the nail pusher is over the last nail, thus pushing
the nail strip in the magazine completely to the front.
Note: Do not let the magazine slider snap back without guiding it. Other-
wise, the magazine slider could become damaged, and there is danger of
your fingers being caught or pinched.
Rated pressure
bar 4–8
Connecting thread
"3/8
Supply-air hose
– Max. operating pressure at 20 °C
– Inner diameter of hose
–Max. hose length
bar
"
m
10
3/8
30
Air consumption per driving proce-
dure
at 6.8 bar (100 psi)
l1.46
Dimensions
–Height
–Width
–Length
mm
mm
mm
307
79
320
Weight according to EPTA-Procedure
01/2003
kg 1.86
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
Compressed-air nailer GSK 64-34
Professional
OBJ_BUCH-1302-001.book Page 17 Tuesday, March 22, 2011 11:17 AM
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSK 64-34 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSK 64-34 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info