592525
14
Zoom out
Zoom in
Previous page
1/85
Next page
1 609 929 N55 | (14.11.07) Bosch Power Tools
14 | English
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1
forward so that the “I” is indicated on the switch.
To switch off the machine, push the On/Off
switch 1 toward the rear so that the “0” is indi-
cated on the switch.
Working Advice
Apply the power tool to the workpiece only when
switched on.
Hold the power tool inclined in an angle of 15° to
the surface of the steel sheet and do not tilt it lat-
erally.
Guide the machine evenly and with light feed in
the cutting direction. Excessive feed significantly
reduces the service life of the saw blade and can
cause damage to the power tool.
f Wear protective gloves while working and
pay particular attention to the mains cable.
Sharp burrs develop at the cut steel sheet and
can cause injuries to the operator or damage
the mains cable.
When cutting curves, make sure not to tilt the pow-
er tool laterally and work with low feed rate only.
Maximum Steel Sheet Cutting Capacity
The maximum steel sheet cutting capacity d
max
depends on the strength properties of the ma-
terial to be cut.
The machine allows for cutting of metal sheet to
the following thicknesses:
Adjusting Cutter Clearance a
The cutter clearance a (gap be-
tween the cutters) depends on
the sheet thickness d
max
to be cut.
For softer or more ductile materials, the
clearance a must be decreased; for harder or
more brittle materials, increased.
Loosen the fastening screw 12 for the bottom
cutter. Adjust the requested cutter clearance a
with the adjustment screw 11. The upper cutter
7 and the bottom cutter 9 may not touch each
other. Check the clearance with the setting
gauge 13. Retighten the fastening screw 12 for
the bottom cutter.
15
˚
Material Max. strength property
[N/mm
2
]
d
max
[mm]
Steel 400 2.8
600 2.2
800 1.9
Aluminium 200 3.5
d
max
[mm]
Cutter clearance a
[mm]
0.2
1.4 0.3
1.5
2.8 0.5
a
OBJ_BUCH-598-001.book Page 14 Wednesday, November 14, 2007 10:16 AM
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSC 2.8 Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSC 2.8 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info