786166
14
Zoom out
Zoom in
Previous page
1/191
Next page
14 | English
Material max. strength
(N/mm2)dmax
(mm)
600 1.2
800 0.7
Aluminium 200 2.2
Adjusting cutter clearance "a"
The cutter clearancea (gap between the
cutters) depends on the sheet thickness
dmax to be cut.
The clearance a between the cutters should be 10% of the
maximum sheet thickness (e.g. 0.1mm cutter clearance for
1mm sheet thickness).
For softer or more ductile materials, the clearancea must be
decreased; for harder or more brittle materials, it must be in-
creased.
Loosen the fastening screw(10) for the bottom cutter. Ad-
just the requested cutter clearance a with the set screw(9)
for the bottom cutter. The upper cutter(7) and the bottom
cutter(8) may not touch each other.
Check the clearance with a commercially available setting
gauge. Retighten the fastening screw(10) for the bottom
cutter with a tightening torque of 3–4Nm.
Temperature Dependent Overload Protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the battery tem-
perature is outside the permitted range, the stroke rate is re-
duced or the power tool shuts down. When the stroke rate is
reduced, the power tool will not run at the full stroke rate
again until the battery temperature is back within the permit-
ted range. In the event of automatic shutdown, switch off the
power tool and allow the battery to cool down before switch-
ing the tool on again.
Maintenance and Service
Maintenance and Cleaning
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
uTo ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
Changing the cutter (seefigureA)
The upper cutter(7) and the bottom cutter(8) are identical,
have four cutting edges each, and can be exchanged with
each other.
Turn or replace the cutters in good time. Only sharp applica-
tion tools achieve good cutting capacity and make the power
tool last longer.
To replace the upper cutter(7) loosen the fastening
screw(6), to replace the bottom cutter(8) loosen the
fastening screw(10).
Turn the cutter by 90° or install a new cutter. When installing
the bottom cutter(8), ensure that it fits against the set
screw(9).
Note: Turn the cutter only in the direction indicated in the
figureA and only insert a new cutter in the position shown in
the figure. Cutting is not possible with an incorrectly inser-
ted cutter.
Retighten the fastening screw(6) for the upper cutter and
the fastening screw(10) for the bottom cutter with a tight-
ening torque of 3–4Nm. Check the cutter clearance a as de-
scribed above.
Upper cutter(7) and bottom cutter(8) may not be re-
ground.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
1 609 92A 7XM | (26.07.2022) Bosch Power Tools
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GSC 18V-16 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSC 18V-16 E in the language / languages: All languages as an attachment in your email.

The manual is 3.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info