Manual Bosch GSB 20-2 RCE (page 22 of 137) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

78438

Zoom out

Zoom in

1/137

1 609 929 M38 | (11.9.07) Bosch Power Tools

22 | English

Assembly

Auxiliary Handle (see figure A)

f Operate your machine only with the auxiliary

handle 12.

The auxiliary handle 12 can be set to any position

for a secure and low-fatigue working posture.

Turn the bottom part of the auxiliary handle 12 in

counterclockwise direction and swivel the auxil-

iary handle 12 to the desired position. Then

retighten the bottom part of the auxiliary handle

12 by turning in clockwise direction.

Adjusting the Drilling Depth (see figure A)

The required drilling depth X can be set with the

depth stop 13.

Press the button for the depth stop adjustment

11 and insert the depth stop into the auxiliary

handle 12.

Pull out the depth stop until the distance be-

tween the tip of the drill bit and the tip of the

depth stop correspond with the desired drilling

depth X.

The knurled surface of the depth stop 13 must

face upward.

Changing the Tool

f Before any work on the machine itself, pull

the mains plug.

Keyless Chuck (see figure B)

The drill spindle is locked when the On/Off

switch 7 is not pressed. This makes quick, con-

venient and easy changing of the tool in the drill

chuck possible.

Open the keyless chuck 1 by turning in rotation

direction n, until the tool can be inserted. Insert

the tool.

Firmly tighten the collar of the keyless chuck 1 by

hand in rotation direction o until the locking ac-

tion (“click”) is no longer heard. This automati-

cally locks the chuck.

The locking is released again to remove the tool

when the collar is turned in the opposite direc-

tion.

Key Type Drill Chuck (see figure C)

f Wear protective gloves when changing the

tool. The drill chuck can become very hot dur-

ing longer work periods.

Open the key type drill chuck 15 by turning until

the tool can be inserted. Insert the tool.

Insert the chuck key 14 into the corresponding

holes of the key type drill chuck 15 and clamp the

tool uniformly.

Screwdriver Tools (see figure D)

When working with screwdriver bits 16, a univer-

sal bit holder 17 should always be used. Use only

screwdriver bits that fit the screw head.

For driving screws, always position the “Drill-

ing/Impact Drilling” selector switch 2 to the

“Drilling” symbol.

Replacing the Drill Chuck

f Before any work on the machine itself, pull

the mains plug.

f For power tools without spindle lock, the

drill chuck must be replaced by an author-

ised after-sales service agent for Bosch pow-

er tools.

Removing the Drill Chuck (see figure E)

Disassemble the auxiliary handle and set the gear

selector 10 to the centre position between the

1st and 2nd gear.

Insert a steel pin with a diameter of

Ø 4 mm and

approx. 50 mm of length into the drill hole on the

spindle neck in order to lock the drill spindle.

Clamp the short end of an Allen key 18 into the

keyless chuck 1.

Place the machine on a stable surface (e.g. a

workbench). Hold the machine firmly and loosen

the keyless chuck 1 by turning the Allen key 18 in

rotation direction n. Loosen a tight-seated key-

less chuck by giving the long end of the Allen key

18 a light blow. Remove the Allen key from the

keyless chuck and completely unscrew the key-

less chuck.

OBJ_BUCH-115-002.book Page 22 Tuesday, September 11, 2007 2:39 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GSB 20-2 RCE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch GSB 20-2 RCE

Bosch GSB 20-2 RCE User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 136 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GSB 20-2 RCE Manual

Product: