786295
19
Zoom out
Zoom in
Previous page
1/287
Next page
English | 19
Battery model ProCORE18V...
LED Capacity
5 × continuous green light 80–100%
4 × continuous green light 60–80%
3 × continuous green light 40–60%
2 × continuous green light 20–40%
1 × continuous green light 5–20%
1 × flashing green light 0–5%
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50°C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Operation
Suitable blind rivet/nosepiece combinations
The use of a combination not listed in the table below may
lead to poor fastening or a malfunction of the power tool.
Blind rivet Nosepiece
Size Rivet mandrel Labelling Hole diameter
Dia.3.0mm (1/8")
Dia.3.2mm (1/8") Dia.2.00−2.15mm
Dia.1.85−2.15mm 3.0/3.2 Dia.2.3−2.4mm
Dia.4.0mm (5/32") Dia.2.35−2.80mm 4.0 Dia.2.7−2.8mm
Dia.4.8mm (3/16")
Dia.5.0mm (3/16") Dia.2.77−3.50mm
Dia.2.95−3.50mm 4.8/5.0 Dia.3.3−3.4mm
Dia.6.0mm (1/4")
Dia.6.4mm (1/4") Dia.3.40−3.50mm
Dia.3.71−4.00mm 6.4 Dia.4.6−4.7mm
Setting a blind rivet (see figuresA1–A3)
Prepare the workpieces to be connected. If no holes are
yet available, pre-drill the workpieces.
Select a suitable nosepiece(1). Screw the nosepiece
onto the cover sleeve(2) and tighten it with the
wrench(9).
Use the AUTO(18) button to select the required working
mode(see "Selecting the working mode", page20).
Insert the rivet mandrel of the blind rivet(20) into the
nosepiece(1).
Hold the power tool tightly and push the blind rivet into
the pilot hole.
Depending on the working mode, press the on/off
switch(12) and wait until the rivet mandrel has broken
off.
Tilt the power tool backwards so that the rivet mandrel
can fall into the mandrel container(5).
Note:After setting the blind rivet, ensure that the broken-off
rivet mandrel has fallen into the mandrel container before
setting the next blind rivet.
Changing the Nosepiece (see figureB)
The nosepiece magazine(4) contains nosepieces of three
different sizes, enabling the user to exchange nosepieces
quickly.
Use the wrench(9) to unscrew the nosepiece(1) from
the cover sleeve(2).
Screw the new nosepiece on and tighten it with the
wrench(9).
Empty the mandrel container (seefigureC)
Always empty the mandrel container(5) for broken-off rivet
mandrels before it is completely full in order to prevent
blockages.
Unscrew the mandrel container(5) by turning it anti-
clockwise.
Empty the mandrel container(5) into a suitable recycling
or waste bin.
Screw the mandrel container (5) back onto the power
tool by turning it clockwise.
Bosch Power Tools 1 609 92A 7R1 | (22.06.2022)
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GRG 18V-16 C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GRG 18V-16 C in the language / languages: All languages as an attachment in your email.

The manual is 5.83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info