809325

Bosch Greensource Hydrolight - Hydrocomfort Manual

11
Zoom out
Zoom in
Previous page
1/20
Next page
LCD ROOM CONTROLLER (ACCESSORY)
6 720 806 630 (2013/02) 11
Fig. 23
Call up Alarm log:
▶Select Alarm.
▶Select Alarm log.
The info icon ( Fig. 4, [12]) is shown on the display if an event occurs
which does not require immediate inspection but is stored in Info log.
The icon is shown on the display until the text in the information report
is read.
Call up Info log:
▶Select Alarm.
▶Select Info log.
10.7 ACCESS LEVEL
This menu is used by the installer and the service engineer. Standard is
the customer level, Level = 0.
10.8 RETURN TO FACTORY SETTINGS
Fig. 24
Restore factory settings:
▶ Select the Return to factory settings.
▶ Select the Yes.
▶Select Save to save the change or Cancel to return without saving.
This does not affect the settings made in the Installer/Service level.
10.9 DEACTIVATE ALARM BUZZER
When an alarm occurs, an alarm window is displayed and a warning
signal sounds. This warning signal is turned off if the alarm is
acknowledged or returned ( Chapter 13).
Deactivate alarm buzzer:
▶ Select the Deactivate alarm buzzer.
▶ Select the Yes.
▶Select Save to save the change or Cancel to return without saving.
10.10 PROGRAM VERSION
The program version of the control unit is displayed. It is useful to have
this information on hand when contacting the installer.
11 LCD ROOM CONTROLLER (ACCESSORY)
The control unit supports up to two room controllers, one for each
heating circuit.
Fig. 25 CAN-BUS LCD room controller
THE DISPLAY FUNCTIONS
Fig. 26 Display
[1] Outside temperature display
[2] Room temperature display
[3] Current heating circuit
The display window shows the current room temperature. When
Outdoor temperature display in room sensor (room controller) is set
to Yes the outdoor temperature is also shown, alternating with the room
temperature. This is valid for all installed room controllers.
With certain categories of alarm, the alarm is displayed on the room
temperature sensor display. In this case, the display slowly flashes red
until the alarm is confirmed or automatically reset on the heat pump
controller.
SETTING THE ROOM TEMPERATURE WHEN A ROOM CONTROLLER
HAS BEEN INSTALLED
The room temperature can easily be set using the room controller.
▶ Turn the room controller knob to set the desired room temperature for
the circuit. The previous set value is shown with blinking digits.
The display flashes the setting and stops flashing shortly after turning
the dial has stopped. The value in the control unit menu Room
temperature setting for the circuit is automatically set to the same
value.
Alternatively the desired room temperature is set via the control panel.
▶ Go to the menu Room temperature setting for the circuit and set the
desired room temperature.
The room temperature value in the room controller for the circuit is
automatically set to the same value.
With certain categories of alarm, the alarm is displayed on the room
temperature sensor display. In this case, the display slowly flashes red
until the alarm is confirmed or automatically reset on the heat pump
controller.
The room controller has the function to provide:
▶ Change room temperature setting
▶ Shows the actual room temperature
▶ Shows the outdoor temperature (if chose in the
display)
▶ Flashes when there is an alarm in the display
6 720 641 467-59.1I
6 720 641 467-60.1I
1234567
6 720 648 126-04.1I
12
3
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Greensource Hydrolight - Hydrocomfort at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Greensource Hydrolight - Hydrocomfort in the language / languages: English as an attachment in your email.

The manual is 1.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info