592509
15
Zoom out
Zoom in
Previous page
1/201
Next page
16 | English
1 609 92A 114 | (16.12.14) Bosch Power Tools
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 16.12.2014
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Operate your machine only with the auxiliary handle 7
or bow handle 2.
Auxiliary Handle
Screw the auxiliary handle 7 on the right or left of the machine
head depending on the working method.
Bow Handle
Fasten the bow handle 2 to the gear case as shown in the fig-
ure.
Mounting the Grinding Tools
Before any work on the machine itself, pull the mains
plug.
Clean the grinder spindle 6 and all parts to be mounted.
For clamping and loosening the grinding tools, lock the grind-
er spindle with the spindle lock button 3.
Actuate the spindle lock button only when the grinder
spindle is at a standstill. Otherwise, the machine may be-
come damaged.
See graphics page for the mounting sequence.
Buffing Disc
Screw the clamping mandrel 8 firmly onto grinder spindle 6
and tighten it via the spanner surfaces with an open-end span-
ner.
Mount the clamping flange 9 and the buffing disc 10 onto the
clamping mandrel 8. Screw on the clamping nut 11 and tight-
en with the two-pin spanner.
Polishing Plate
Mount the two spacer discs 12 and the polishing plate 13 on-
to the spindle 6.
Screw on the round nut 14 and tighten with the two-pin span-
ner.
Pull the lamb’s wool bonnet 15 over the polishing plate 13
and tighten the attachment strings.
Polishing Sponge
Screw the polishing sponge 16 firmly onto the grinder spindle
6. The lambskin polishing bonnet 17 can be pulled over the
polishing sponge 16.
Rubber Sanding Plate
Place the rubber sanding plate 18 onto the grinder spindle 6.
Screw on the round nut 14 and tighten with the two-pin span-
ner.
Firmly press the sanding sheet 19 onto the bottom side of the
rubber sanding plate 18.
Felt Polishing Disc
Firmly screw the felt polishing disc 20 onto the grinder spin-
dle 6.
Cup Brush/Disc Brush
The cup brush/disc brush must be able to be screwed onto
the grinder spindle until it rests firmly against the grinder
spindle flange at the end of the grinder spindle threads. Tight-
en the cup brush/disc brush with an open-end spanner.
Approved Grinding Tools
All grinding tools mentioned in these operating instructions
can be used.
The permissible speed [min
-1
] or the circumferential speed
[m/s] of the grinding tools used must at least match the values
given in the table.
Therefore, observe the permissible rotational/circumferen-
tial speed on the label of the grinding tool.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
Provide for good ventilation of the working place.
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
max.
[mm]
[mm]
D b d [min
-1
] [m/s]
180 3000 80
100 30 M 14 3000 45
D
D
b
d
OBJ_BUCH-1284-003.book Page 16 Tuesday, December 16, 2014 4:09 PM
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GPO 14 CE Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GPO 14 CE Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info