Manual Bosch GOP 40-30 Professional (page 22 of 304) (All languages)

640565

Zoom out

Zoom in

1/304

22 | English

1 609 92A 18M | (14.12.15) Bosch Power Tools

When doing so, place the application tool/accessory in a posi-

tion which is convenient for the job at hand. Twelve different

positions are possible, each offset by 30°.

Press the application tool/accessory in the required position

firmly onto the clamping jaws of the tool holder until it is auto-

matically locked.

 Check the tight seating of the application tool/accesso-

ry. Incorrect or not securely fastened application tools/ac-

cessories can come loose during operation and pose a haz-

ard.

Mounting and Adjusting the Depth Stop

The depth stop 15 can be used when working with segment

and plunge cut saw blades.

If required, remove an already mounted application tool/ac-

cessory.

Slide the depth stop 15 in the required work position all the

way over the tool holder 4 onto the collar of the power tool. Al-

low the depth stop to engage. Twelve different positions are

possible, each offset by 30°.

Set the required working depth. Press shut the clamping lever

14 of the depth stop in order to fix the depth stop.

Mounting/Replacing a Sanding Sheet on the Sanding

Plate

The sanding plate 9 is fitted with Velcro backing for quick and

easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 10, free the Velcro back-

ing of the sanding plate 9 from any debris by tapping against

it in order to enable optimum adhesion.

Position the sanding sheet 10 flush alongside one edge of the

sanding plate 9, then lay the sanding sheet onto the sanding

plate and press firmly.

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

To remove the sanding sheet 10, grasp it at one of the tips and

pull it off from the sanding plate 9.

You can use all sanding sheets, fleece pads/polishing cloth

pads of the Delta 93 mm series of Bosch accessory program.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:

Dust/Chip Extraction

 Dust from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dust can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dust, such as oak or beech dust, is considered car-

cinogenic, especially in connection with wood-treatment

additives (chromate, wood preservative). Materials con-

taining asbestos may only be worked by specialists.

–As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dust can

easily ignite.

Sanding disc Material Application Grain size

–All wooden materials

(e. g., hardwood,

softwood, chipboard,

building board)

–Metal materials

For coarse-sanding, e. g. of rough, unplaned beams and

boards

coarse 40

For face sanding and planing small irregularities

medium 80

100

120

For finish and fine sanding of wood

fine 180

240

320

400

–Paint

–Varnish

– Filling compound

– Filler

For sanding off paint

coarse 40

For sanding primer (e. g., for removing brush dashes,

drops of paint and paint run)

medium 80

100

120

For final sanding of primers before coating

fine 180

240

320

400

OBJ_BUCH-2566-001.book Page 22 Monday, December 14, 2015 4:27 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GOP 40-30 Professional in the language / languages: All languages as an attachment in your email.

The manual is 20,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GOP 40-30 Professional Manual

Product: