544108

Bosch GOP 18 V-EC Manual

17
Zoom out
Zoom in
Previous page
1/213
Next page
English | 17
Bosch Power Tools 2 609 140 973 | (31.5.13)
To remove the sanding sheet 13, grasp it at one of the tips and
pull it off from the sanding plate 12.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Connecting the Dust Extraction (see figure A)
For sanding, always connect the dust extraction.
Remove the application tool/accessory when mounting the
dust extraction 17 (accessory).
If required, assemble the parts of the dust extraction 17 as
shown in the figure. Position the assembled dust extraction
onto the machine via the tool holder 9. Turn the dust extrac-
tion in such a manner that the cams of the dust extraction en-
gage into the corresponding recesses on the housing. Fasten
the dust extraction to the machine with the retaining clip 15
as shown in the figure.
Pay attention that the felt ring 14 is undamaged and faces
tightly against the sanding plate 12. Replace a damage felt
ring immediately.
Depending on the machine model, place a vacuum hose 18
(accessory) either directly onto the vacuum connection 16 or
cut off the old hose end, screw the extraction adapter 19 (ac-
cessory) onto the hose end and insert it directly into the vac-
uum connection 16. Connect the vacuum hose 18 with a vac-
uum cleaner (accessory). An overview for the connection of
various vacuum cleaners can be found at the end of these in-
structions.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Operation
Starting Operation
Inserting the battery
Use only original Bosch lithium ion batteries with the
voltage listed on the nameplate of your power tool. Using
other batteries can lead to injuries and pose a fire hazard.
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
Insert the charged battery pack 5 from the rear into the base
of the power tool. Press the battery pack completely into the
base until the red stripe can no longer be seen and the battery
pack is securely locked.
Sanding disc Material Application Grain size
– All wooden materials
(e.g., hardwood, soft-
wood, chipboard, build-
ing board)
– Metal materials
For coarse-sanding, e.g. of rough, unplaned beams and
boards
coarse 40
60
For face sanding and planing small irregularities
medium 80
100
120
For finish and fine sanding of wood
fine 180
240
320
400
–Paint
–Varnish
– Filling compound
–Filler
For sanding off paint
coarse 40
60
For sanding primer (e.g., for removing brush dashes, drops
of paint and paint run)
medium 80
100
120
For final sanding of primers before coating
fine 180
240
320
400
OBJ_BUCH-1808-001.book Page 17 Friday, May 31, 2013 9:29 AM
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GOP 18 V-EC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GOP 18 V-EC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info