544108
16
Zoom out
Zoom in
Previous page
1/213
Next page
16 | English
2 609 140 973 | (31.5.13) Bosch Power Tools
Removing the battery
The battery 5 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 3 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 5, press the battery unlocking button 3
and pull the battery out of the power tool toward the rear. Do
not exert any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
6 indicate the charge condition of the battery 5. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 7 to indicate the charge condition. This is also
possible when the battery 5 is removed.
When no LED lights up after pushing button 7, then the bat-
tery is defective and must be replaced.
Changing the Tool
Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Wear protective gloves when changing application
tools/accessories. Contact with the application tool/ac-
cessoriy can lead to injuries.
Selecting the Application Tool/Accessory
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/
accessory.
For this, open the SDS lever 8 to the stop (not further) and
remove the application tool.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 11) in such a manner on the tool holder 9 that
the offset faces downward (see illustration on the graphics
page; marking on the application tool/accessory is readable
from above).
Turn the application tool/accessory to a position favourable
for the respective job, and allow it to engage into the cams of
the tool holder 9. 12 different positions are possible, each
offset by 30°.
Close SDS lever 8 so that it faces against the housing of the
power tool.
Check the tight seating of the application tool/acces-
sory. Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose a
hazard.
Mounting/Replacing a Sanding Sheet on the Sanding Plate
The sanding plate 12 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 13, free the Velcro back-
ing of the sanding plate 12 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 13 flush alongside one edge of the
sanding plate 12, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
LED Capacity
Continuous lighting 3 x green 2/3
Continuous lighting 2 x green 1/3
Continuous lighting 1 x green <1/3
Flashing light 1 x green Reserve
Accessory Material
HCS wood seg-
ment saw blade*
Wooden materials,
plastic
BIM segment saw
blade*
Wooden materials,
plastic, non-ferrous
metals
HCS plunge cut
saw blades,
wood*
Wooden materials,
plastic, gypsum and
other soft materials
BIM plunge cut
saw blades,
metal*
Metal (e.g. unhard-
ened nails, screws,
smaller profiles),
non-ferrous metals
BIM plunge cut
saw blade, wood
and metal*
Wood, metal, non-
ferrous metals
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
HM-Riff segment
saw blade*
Grouting joints, soft
wall tiles, glass-fibre
reinforces plastic
and other abrasive
materials
HM-Riff delta
plate*
Scraper, rigid* Carpets, coverings
Scraper, flexible* Silicone and other
elastic materials
Base plate for
sanding, series
Delta 93 mm*
Depends on sanding
sheet
Accessory Material
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
OBJ_BUCH-1808-001.book Page 16 Friday, May 31, 2013 9:29 AM
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GOP 18 V-EC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GOP 18 V-EC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info