544272
13
Zoom out
Zoom in
Previous page
1/105
Next page
English | 13
Bosch Power Tools 1 609 929 N87 | (13.2.09)
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine.
Switching On and Off
f Before starting the machine, place the pow-
er tool in such a manner on both rear chaser
rollers 3 that the diamond cutting discs do
not touch the workpiece. Otherwise, the
diamond cutting discs can touch the work-
piece, resulting in possible loss of control
over the power tool when switching on.
To start the power tool, press the On/Off switch
1 forward and then down.
To lock-on the pressed On/Off switch 1, push
the On/Off switch 1 further forward.
To switch off the power tool, release the On/Off
switch 1, or when it is locked, briefly press the
On/Off switch 1 and then release it.
Switch Version without Lock-on
(country-specific):
To start the power tool, press the On/Off switch
1 forward and then down.
To switch off the machine, release the On/Off
switch 1.
f Never set down a coasting machine on the
chaser rollers 3, but always aside, so that
the diamond cutting discs can rotate freely
and do not face toward your body.
f Check the diamond cutting discs before
use. The diamond cutting disc(s) must be
mounted properly and be able to rotate
freely. Carry out a test run for at least one
minute without any load. Do not use dia-
mond cutting discs that are damaged, out-
of-balance, or vibrate. Damaged diamond
cutting discs can rupture and lead to injuries.
Reduced starting current
The electronic reduced starting current limits
the power consumption when switching the tool
on and enables operation from a 13 ampere
fuse.
Overload Protection
When overloaded, the motor comes to a stop.
Relieve the load on the machine immediately
and allow to cool down for approx. 30 seconds
at the highest no-load speed.
Restarting Protection
The restarting protection feature prevents un-
controlled restarting of the machine after an in-
terruption in the power supply.
To restart the operation, switch the On/Off
switch 1 to the Off position and start the ma-
chine again.
Note: Check the function of the restarting pro-
tection feature regularly by having the mains
plug pulled during operation and plugged in
again afterwards.
Working Advice
f Exercise caution when cutting slots in
structural walls; see Section “Information
on Structures ”.
f Do not strain the machine so heavily that it
comes to a standstill.
f Clamp the workpiece if it does not remain
stationary due to its own weight.
f The machine may only be used for dry cut-
ting.
f Always guide the machine with both han-
dles. Do not guide or carry the machine by
the elbow.
Adjust the cutting depth, see section “Pre-se-
lecting the Cutting Depth”. To compensate
inaccuracies that occur when breaking away
the fin, the cutting depth must be set approx.
3 mm deeper than the requested slot depth.
OBJ_BUCH-916-001.book Page 13 Friday, February 13, 2009 11:21 AM
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GNF 65 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GNF 65 A in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info