Manual Bosch GLM 150 Professional (page 20 of 319) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

592063

Zoom out

Zoom in

1/319

20 | English

1 609 92A 0KT | (23.4.14) Bosch Power Tools

To to change the unit of measure,

press the function-mode button 3 un-

til the “change unit of measure” indi-

cation appears on the display. Select

the required unit of measure by

pressing the plus button 6 or the mi-

nus button 12.

Measuring Functions

Simple Length Measurement

For length measurements, press button 4 until the “length

measurement” indication appears on the display.

Press the measuring button 7 once

for sighting and once more to take the

measurement.

The measured value is displayed in

the result line c.

For several subsequent length mea-

surements, the last measured results

are displayed in the measured-value lines a.

Continuous Measurement (Tracking)

For continuous measurements, the measuring tool can be

moved relative to the target, whereby the measuring value is

updated approx. every 0.5 seconds. In this manner, as an ex-

ample, you can move a certain distance away from a wall,

while the actual distance can always be read.

For continuous measurements, firstly select the length mea-

suring mode and then press the measuring button 7 until the

“indicator for continuous measurement” appears on the

display. The laser is switched on and the measurement starts

immediately.

The current measured value is dis-

played in the result line c.

Briefly pressing the measuring button

7 ends the continuous measurement.

The last measured value is displayed

in the result line c. Pressing the mea-

suring button 7 for several seconds

restarts a continuous measuring run.

Continuous measurement automatically switches off after

5 min. The last measured value remains indicated in the result

line c.

Minimum/Maximum Measurement (see figure F–G)

The minimum measurement is used to determine the shortest

distance from a fixed reference point. It is used, as an exam-

ple, for determining plumb lines or horizontal partitions.

The maximum measurement is used to determine the greatest

distance from a fixed reference point. It is used, as an exam-

ple, for determining diagonals.

For simple minimum/maximum measurement, firstly select

“length measurement mode” and then press button 13 .

“min” is displayed in result line c for minimum measurement.

For maximum measurements, press button 13 again, so that

“max” is displayed in the result line. Then press the measur-

ing button 7. The laser is switched on and the measurement

starts.

Move the laser back and forth over the requested target (e.g.,

the room corner for determining the diagonal) in such a manner

that the reference point of the measurement (e.g., the tip of the

positioning pin

) always remains at the same location.

Depending on the set mode, the mini-

mum or maximum value is displayed

in the result line c. It is always over-

written, when the current length

measurement value is less than the

present minimal or larger than the

present maximal value. The maximal

(“max”), the minimal (“min”) and the current measuring val-

ue are displayed in the measured-value lines a.

To end the minimum/maximum measurement, briefly press

the measuring button 7. Pressing the measuring button again

starts a new measurement.

The minimum/maximum measurement can also be used for

length measurements within other measuring modes (e.g.

area/surface measurement). For this, press button 13 once

for minimal measurement and twice for maximal measure-

ment each time when determining individual measured val-

ues. Then press the measuring button 7 to switch the laser

beam on. Move the measuring tool in such a manner that the

desired minimum or maximum value is measured, and press

the measuring button 7 to take over the minimum or maxi-

mum value into the current calculation.

For time-delayed length measurements and when in mark-out

mode, minimum/maximum measurements are not possible.

The minimum/maximum measurement automatically switch-

es off after 5 min.

Area Measurement

For area/surface measurements, press button 4 until the indi-

cator for area measurement appears on the display.

Afterwards, measure the length and the width, one after an-

other, in the same manner as a length measurement. The laser

beam remains switched on between both measurements.

Upon completion of the second mea-

surement, the surface is automatical-

ly calculated and displayed in the re-

sult line c. The individual measured

values are displayed in the measured-

value lines a.

Volume Measurement

For volume measurements, press button 4 until the indicator

for volume measurement appears on the display.

Afterwards, measure the length, width and the height, one af-

ter another, in the same manner as for a length measurement.

The laser beam remains switched on between all three mea-

surements.

OBJ_BUCH-947-005.book Page 20 Wednesday, April 23, 2014 9:23 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLM 150 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GLM 150 Professional Manual

Product: