Manual Bosch GLM 150 Professional (page 19 of 319) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

592063

Zoom out

Zoom in

1/319

English | 19

Bosch Power Tools 1 609 92A 0KT | (23.4.14)

For switching on the measuring tool, the following possibili-

ties are given:

– Pressing the On/Off button 16: The measuring tool is

switched on and is in length measurement mode. The laser

is not activated.

– Briefly pressing the measuring button 7: Measuring tool

and laser are switched on. The measuring tool is in length

measurement mode.

– Pressing the measuring button 7 for several seconds:

Measuring tool and laser are switched on. The measuring

tool is in continuous measurement mode.

 Do not point the laser beam at persons or animals and

do not look into the laser beam yourself, not even from

a large distance.

To switch off the measuring tool, press the On/Off button 16

for a few seconds.

When no button on the measuring tool is pressed for approx.

5 minutes, the measuring tool automatically switches off to

save the batteries.

When switching off automatically, all stored values are re-

tained.

Measuring Procedure

After switching on, the measuring tool is always in length

measurement or continuous measurement mode. Other

measuring modes can be switched to by pressing the respec-

tive mode button (see “Measuring Functions”, page 20).

After switching on, the rear edge of the measuring tool is pre-

set as the reference level for the measurement. By pressing

the reference level button 8, the reference level can be

changed (see “Selecting the Reference Level

(see figures A – E)”, page 19).

Upon selection of the measuring function and the reference

level, all further steps are carried out by pushing the measur-

ing button 7.

With the reference level selected, place the measuring tool

against the desired measuring line (e.g. a wall).

Briefly press the measuring button 7 to switch on the laser

beam.

 Do not point the laser beam at persons or animals and

do not look into the laser beam yourself, not even from

a large distance.

Aim the laser beam at the target surface. Briefly press the

measuring button 7 again to initate the measurement.

When the laser beam is switched on permanently, the mea-

surement already starts after the first actuation of the mea-

suring button 7. In continuous measurement mode, the mea-

surement starts immediately upon switching on.

Typically, the measured value appears after 0.5 and latest af-

ter 4 seconds. The duration of the measurement depends on

the distance, the light conditions and the reflection proper-

ties of the target surface. The end of the measurement is indi-

cated by a signal tone. The laser beam is switched off auto-

matically upon completion of the measurement.

When no measurement has taken place approx. 20 seconds

after sighting, the laser beam is switched off automatically to

save the batteries.

Selecting the Reference Level (see figures A – E)

For measuring, you can select between four different refer-

ence planes:

– the rear edge of the measuring tool or the front edge of the

laterally folded-out positioning pin 18 (e.g. when measur-

ing onward from outer corners),

– the tip of the folded-out positioning pin 18 (e.g. when

measuring from a corner),

– the front measuring-tool edge (e.g. when measuring on-

ward from a table edge),

–the thread 21 (e.g. for tripod measurements).

To select the reference level, press button 8 until the request-

ed reference level is indicated on the display. Each time after

switching on the measuring tool, the rear end of the measur-

ing tool is preset as the reference level.

Subsequent changing of the reference level for measurements

that have already been carried out (e.g. when indicating mea-

suring values in the measured-value list) is not possible.

Continuous Laser Beam

If required, the measuring tool can also be switched to the

continuous laser beam mode. For this, push the button for

continuous laser beam 2. “LASER” lights up continuously in

the display.

 Do not point the laser beam at persons or animals and

do not look into the laser beam yourself, not even from

a large distance.

In this setting, the laser beam also remains switched on be-

tween measurements; for measuring, it is only required to

press the measuring button 7 once.

To switch off the continuous laser beam, press button 2 again

or switch the measuring tool off.

Switching off the continuous laser beam during a measure-

ment automatically ends the measurement.

Display Illumination

The display illumination is switched on and off by pressing

button 11. When no button is pressed 10 s after switching on

the display illumination, it is switched off to save the batter-

ies.

Audio Signal

To switch the audio signal on and off,

press the function-mode button 3 un-

til the “audio-signal adjustment” indi-

cation appears on the display. Select

the required setting by pressing the

plus button 6 or the minus button 12.

The selected audio-signal adjustment

is retained when switching the measuring tool off and on.

Changing the Unit of Measure

For indication of the measured values, the unit of measure can

be changed at any time.

The following units of measure are possible:

– Length measurement: m, cm, mm,

– Area/surface measurement: m

– Volume measurement: m

OBJ_BUCH-947-005.book Page 19 Wednesday, April 23, 2014 9:23 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLM 150 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GLM 150 Professional Manual

Product: