Manual Bosch GLM 100 C Professional (page 29 of 367) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

592055

Zoom out

Zoom in

1/367

English | 29

Bosch Power Tools 2 609 141 026 | (1.7.13)

Accuracy Check of the Distance Measurement

The accuracy of the distance measurement can be checked as

follows:

– Select a permanently unchangeable measuring section

with a length of approx. 1 to 10 metres; its length must be

precisely known (e.g. the width of a room or a door open-

ing). The measuring distance must be indoors; the target

surface for the measurement must be smooth and reflect

well.

–Measure the distance 10 times after another.

The deviation of the individual measurements from the mean

value must not exceed ±2 mm (max.). Log the measure-

ments, so that you can compare their accuracy at a later point

of time.

Working with the Tripod (Accessory)

The use of a tripod is particularly necessary for larger distanc-

es. Position the measuring tool with the 1/4" thread 19 onto

the quick-change plate of the tripod 29 or a commercially

available camera tripod. Tighten the measuring tool with the

locking screw of the quick-change plate.

Set the corresponding reference level for measurement with

a tripod by pushing button 10 (the reference level is the

thread).

Working with the Measuring Rail (see figures I–K)

The measuring rail 27 can be used for a more accurate grade

measurement result. Distance measurements are not possi-

ble with the measuring rail.

Place the measuring tool into the measur-

ing rail 27 as shown and lock the measur-

ing tool with locking lever 28. Press the

measuring button 2 to activate the “Meas-

uring rail” operating mode.

Regularly check the accuracy of the grade measurement by

carrying out a reversal measurement or with the spirit levels

of the measuring rail.

In case of greater deviation, the measuring tool must be recal-

ibrated. For this, press and hold the grade measurement but-

ton 3. Follow the directions on the display.

When operating the measuring tool in the measuring rail 27,

data transmission is not possible.

To end the “Measuring rail” operating mode, switch the meas-

uring tool off and remove it from the measuring rail.

Troubleshooting – Causes and Corrective

Measures

Cause Corrective Measure

Temperature warning indicator (k) flashing; measure-

ment not possible

The measuring tool is outside the

operating temperature range from

– 10 °C to + 50 ° C (in the function

continuous measurement up to

+40°C).

Wait until the measuring

tool has reached the op-

erating temperature

“ERROR” indication in the display

Addition/Subtraction of measured

values with different units of meas-

ure

Only add/subtract

measured values with

the same units of meas-

ure

The angle between the laser beam

and the target is too acute.

Enlarge the angle be-

tween the laser beam

and the target

The target surface reflects too in-

tensely (e.g. a mirror) or insuffi-

ciently (e.g. black fabric), or the

ambient light is too bright.

Work with the laser tar-

get plate 31 (accessory)

The laser beam outlet 18 or the re-

ception lens 17 are misted up

(e.g. due to a rapid temperature

change).

Wipe the laser beam out-

let 18 and/or the recep-

tion lens 17 dry using a

soft cloth

Calculated value is greater than

1 999 999 or smaller than

–999 999 m/m

Divide calculation into

intermediate steps

Indication “>60 °” or “<–60 °” on the display

The inclination measuring range

for the measuring mode and/or the

reference plane has been exceed-

ed.

Carry out the measure-

ment within the speci-

fied angle range.

“CAL” and “ERROR” indication in the display

The calibration of the grade meas-

urement was not carried out in the

correct sequence or in the correct

positions.

Repeat the calibration

according to the instruc-

tions on the display and

in the operating instruc-

tions.

The surfaces used for the calibra-

tion were not accurately aligned

(horizontal or vertical).

Repeat the calibration

on a horizontal or verti-

cal surface; if required,

check the surface first

with a level.

The measuring tool was moved or

tilted while pressing the button.

Repeat the calibration

and hold the measuring

tool in place while press-

ing the button.

Battery charge-control indicator (g), temperature warn-

ing (k) and “ERROR” indication in the display

Temperature of the measuring tool

not within the allowable charge-

temperature range

Wait until the charge-

temperature range is

reached.

Cause Corrective Measure

OBJ_BUCH-1956-002.book Page 29 Monday, July 1, 2013 11:28 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLM 100 C Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GLM 100 C Professional Manual

Product: