Manual Bosch GLM 100 C Professional (page 26 of 367) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

592055

Zoom out

Zoom in

1/367

26 | English

2 609 141 026 | (1.7.13) Bosch Power Tools

Continuous measurement automatically switches off after

5 min. The last measured value remains indicated in the result

line c.

Indirect Distance Measurement

Note: Indirect distance measurement is always less accurate

than direct distance measurement. Depending on applica-

tion, greater measuring errors are possible than with direct

distance measurement. To improve the measuring accuracy,

we recommend using a tripod (accessory).

The indirect distance measurement is used to measure dis-

tances that cannot be measured directly because an obstacle

would obstruct the laser beam or no target surface is available

as a reflector. This measuring procedure can only be used in

vertical direction. Any deviation in horizontal direction leads

to measuring errors.

The laser beam remains switched on between the individual

measurements.

For indirect length measurements, three measuring modes

are available. Each measuring mode can be used for deter-

mining different distances.

a) Indirect height measurement (see figure C)

Press the function-mode button 8 until the indication for indi-

rect height measurement appears on the display.

Pay attention that the measuring tool is positioned at the

same height as the bottom measuring point. Now, tilt the

measuring tool around the reference plane and measure dis-

tance “1” as for a length measurement.

Upon completion of the measurement,

the result for the sought distance “X” is

displayed in the result line c. The measur-

ing values for the distance “1” and the an-

gle “α”are displayed in the measured-

value lines a.

b) Double indirect height measurement (see figure D)

Press the function-mode button 8 until the indication for dou-

ble indirect height measurement appears on the display.

Measure distances “1” and “2” in this sequence as for a

length measurement.

Upon completion of the measurement,

the result for the sought distance “X” is

displayed in the result line c. The measur-

ing values for the distances “1”, “2” and

the angle “α” are displayed in the meas-

ured-value lines a.

Pay attention that the reference plane of the measurement

(e.g. the rear edge of the measuring tool) remains exactly at

the same location for all individual measurements within a

measuring sequence.

c) Indirect length measurement (see figure E)

Press the function-mode button 8 until the indication for indi-

rect length measurement appears on the display.

Pay attention that the measuring tool is positioned at the

same height as the sought measuring point. Now, tilt the

measuring tool around the reference plane and measure dis-

tance “1” as for a length measurement.

Upon completion of the measurement,

the result for the sought distance

“X” is

displayed in the result line c. The measur-

ing values for the distance “1” and the an-

gle “α” are displayed in the measured-

value lines a.

Wall Surface Measurement (see figure F)

The wall surface measurement is used to determine the sum

of several individual surfaces with a common height.

In the example shown, the total surface of several walls that

have the same room height A, but different lengths B, are to

be determined.

For wall surface measurements, press the function-mode but-

ton 8 until the indicator for wall surface measurement ap-

pears on the display.

Measure the room height A as for a length measurement. The

measured value (“cst”) is displayed in the top measured-val-

ue line a. The laser remains switched on.

Afterwards, measure length B

of the first

wall. The surface is automatically calcu-

lated and displayed in the result line c.

The length measurement value is dis-

played in the centre measured-value line

a. The laser remains switched on.

Now, measure length B

of the second

wall. The individually measured value dis-

played in the centre measured-value line

a is added to the length B

. The sum of

both lengths (“sum”, displayed in the

bottom measured-value line a) is multi-

plied with the stored height A. The total

surface value is displayed in the result line c.

In this manner, you can measure any number of further

lengths B

, which are automatically added and multiplied with

height A.

The condition for a correct area/surface calculation is that the

first measured length (in the example the room height A) is

identical for all partial surfaces.

Grade Measurement (see figure G)

After pressing the grade measurement button 3, the indica-

tion for grade measurement appears on the display . The

backside of the measuring tool is used as the reference plane.

By pressing the grade measurement button 3 again, the side

surfaces of the measuring tool are used as reference plane

and the display view is shown turned by 90°.

Press the measuring button 2 to lock the measuring value and

accept it in the measured values memory. Pressing the meas-

uring button 2 again continues the measurement.

When the indication flashes during the measuring procedure,

then the measuring tool was tilted too much in lateral direc-

tion.

OBJ_BUCH-1956-002.book Page 26 Monday, July 1, 2013 11:28 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLM 100 C Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GLM 100 C Professional Manual

Product: