786132
19
Zoom out
Zoom in
Previous page
1/275
Next page
English | 19
ons, it is only possible to check the state of charge when the
power tool is at a standstill.
Press the on/off switch (4) halfway or completely to display
the state of charge.
LED Capacity
Continuous lighting 3 x green ≥ 2/3
Continuous lighting 2 x green ≥ 1/3
Continuous lighting 1 x green < 1/3
Flashing light 1 x green Reserve
If no LED lights up after pressing the on/off switch (4), then
the battery is defective and must be replaced.
Inserting/changing the circular saw blade
uRemove the battery before carrying out any work on
the power tool.
uWear protective gloves when fitting the saw blade.
Danger of injury when touching the saw blade.
uOnly use saw blades that match the specifications
given in this operating manual and that are tested and
marked in accordance with EN 847-1
uThe permitted speed of the application tool must be at
least equal to the maximum speed marked on the
power tool. If accessories run faster than their rated
speed, they may break and fly off.
uDo not use abrasive wheels as the application tool un-
der any circumstances.
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions.
Removing the saw blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
Press and hold the spindle lock button (6).
uDo not press the spindle lock button (6) while the saw
spindle is moving. The power tool may become damaged
if this happens.
Use the hex key (5) to undo the clamping bolt (25) in ro-
tational direction .
Swing the retracting blade guard (21) back and hold on
to it firmly.
Remove the clamping flange (24) and the saw blade (23)
from the saw spindle (20).
Fitting the saw blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
Clean the saw blade (23) and all the clamping elements
to be fitted.
Swing the retracting blade guard (21) back and hold on
to it firmly.
Place the saw blade (23) on the mounting flange (22).
The cutting direction of the teeth (direction of the arrow
on the saw blade) must match the rotational direction of
the arrow on the protective guard (21).
Attach the clamping flange (24) and screw in the clamp-
ing bolt (25) in rotational direction . Ensure that the
mounting flange (22) and clamping flange (24) are in-
stalled in the correct position.
Press and hold the spindle lock button (6).
Use the hex key (5) to tighten the clamping bolt (25) in
rotational direction . The tightening torque should be
6–9Nm, which corresponds to hand-tight plus ¼ turn.
Dust/chip extraction
The dust from materials such as lead paint, certain types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
To achieve a high level of dust extraction, use a suitable
dust extractor together with this power tool.
Provide good ventilation at the workplace.
It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
uAvoid dust accumulation at the workplace. Dust can
easily ignite.
Fitting the dust extraction adapter (see figure B)
Fasten the dust extraction adapter (29) to the base plate (7)
using the fastening screw (28).
A dust extraction hose with a diameter of 19mm can be con-
nected to the dust extraction adapter (29).
uThe dust extraction adapter must only be fitted if an
external dust extraction system is connected. Other-
wise the extraction duct can become clogged.
uNo dust bags should be connected to the dust extrac-
tion adapter. Otherwise the extraction system can be-
come clogged.
To ensure optimum extraction, the dust extraction adapter
(29) must be cleaned regularly.
External dust extraction
Connect the dust extraction hose (30) to a dust extractor
(accessory). You will find an overview of how to connect to
various dust extractors at the end of these operating instruc-
tions.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Bosch Power Tools 1 609 92A 7TA | (17.05.2022)
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GKS 12V-26 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GKS 12V-26 in the language / languages: All languages as an attachment in your email.

The manual is 6.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info