Manual Bosch GHO 40-82 C Professional (page 15 of 163) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

593159

Zoom out

Zoom in

1/163

English | 15

Bosch Power Tools 1 619 929 J65 | (12.10.11)

Constant Electronic Control

Constant electronic control holds the speed constant at no-

load and under load, and ensures uniform working perform-

ance.

Soft Starting

The electronic soft-starting feature limits the torque when

switching on and increases the working life of the motor and

drive belt.

Temperature Dependent Overload Protection

In case of overload, the speed is reduced. Allow the machine

to cool down by running it at maximum no-load speed for ap-

prox. 30 seconds.

Working Advice

Planing (see figure G)

Set the required planing depth and place the front part of the

planer base plate 10 against the workpiece.

f Apply the machine to the workpiece only when

switched on. Otherwise there is danger of kickback when

the cutting tool jams in the workpiece.

Switch the machine on and guide the machine with even feed

over the surface to be planed.

To achieve high-grade surfaces, work only with low feed and

apply pressure on the centre of the planer base plate.

When machining hard materials (e.g. hardwood) as well as

when utilising the maximum planer width, set only low planing

depths and reduce planer feed, as required.

Excessive feed reduces the surface quality and can lead to

rapid clogging of the chip ejector.

Only sharp blades achieve good cutting capacity and give the

machine longer life.

The integrated park rest 28 also allows for continued planing

at any given location on the workpiece after an interruption:

– With the park rest folded down, place the machine on the

location of the workpiece where the planing is to be contin-

ued.

– Switch on the machine.

– Apply the supporting pressure onto the front part of the

planer base plate and slowly push the machine forward

(n). This tilts the park rest upward (o) so that the rear

part of the planer base plate faces on the workpiece again.

– Guide the machine over the surface to be planed (p) with

even feed.

Beveling Edges (see figure H)

The V-grooves in the front planer base plate allow quick and

easy beveling of workpiece edges. Depending on required

bevel width, use the corresponding V-groove. For this, place

the planer with the V-groove onto the edge of the workpiece

and guide it along the edge.

Planing with Parallel/Beveling Guide (see figures D–F)

Mount the parallel guide 21 or beveling guide 24 to the ma-

chine using the corresponding fastening bolt 23. Depending

on the application, mount the rebating depth stop 27 with fas-

tening bolt 26 to the machine.

Loosen locking nut 22 and adjust the desired rebating width.

Retighten locking nut 22.

Adjust the requested rebating depth accordingly with the re-

bating depth stop 27.

Carry out the planing procedure several times until the re-

quested rebating depth is reached. Guide the planer applying

sideward supporting pressure.

Beveling with the Beveling Guide

When beveling rebates and

surfaces, adjust the required

slope angle with the angle ad-

justment 25.

Storage Compartment for Planer Blade/Allen Key

A planer blade 16 and an Allen key 18 can be housed in the

storage compartment 3 as shown in the figure. To remove the

contents in the compartment, completely pull the storage

compartment for the planer blade/Allen key 3 out of the plan-

er.

Service Station (seefigure I)

The service station 29 in the carrying case can be used for

holding the planer, e. g. for changing the blade.

f Do not use the service station for stationary operation

of the planer.

Groove to be used Dimension a

(mm)

none 0 – 5.7

small 1.9 – 7.6

medium 4.7 – 10.3

large 5.9 – 11.6

OBJ_BUCH-633-004.book Page 15 Wednesday, October 12, 2011 11:07 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GHO 40-82 C Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GHO 40-82 C Professional Manual

Product: