Manual Bosch GHO 40-82 C Professional (page 14 of 163) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

593159

Zoom out

Zoom in

1/163

14 | English

1 619 929 J65 | (12.10.11) Bosch Power Tools

Assembly

f Before any work on the machine itself, pull the mains

plug.

Changing the Tool

f Be cautious when replacing the planer blades. Do not

grasp the planer blades by the cutting edges. Possible

danger of injury due to the sharp cutting edges of the plan-

er blades.

Use only original Bosch carbide blades (TC).

The carbide blade (TC) has 2 cutting edges and can be re-

versed. When both cutting edges are dull, the planer blade 16

must be replaced. The carbide blade (TC) may not be resharp-

ened.

Disassembling the Planer Blade(s) (see figure A)

To reverse or replace the planer blade 16, rotate the blade

drum 13 until it is parallel to the planer base plate 10.

n Loosen the two fastening screws 15 with the Allen key

18 by approx. 1 – 2 turns.

o If necessary, loosen the clamping element 14 by giving it

a light blow with a suitable tool (e.g. a wooden wedge).

p Fold the lateral blade-shaft protector 17 down and push

the carbide blade 16 sideward out of the blade drum 13

using a piece of wood.

Assembling the Planer Blade(s) (see figure B)

The guide groove of the planer blade always ensures continu-

ous height adjustment when replacing or reversing it.

If required, clean the blade seat in the clamping element 14

and the planer blade 16.

When assembling the planer blade, ensure that it is seated

properly in the blade holder of the clamping element 14 and

aligned flush at the side edge of the rear planer base plate 10.

Afterwards tighten the 2 fastening screws 15 again with the

Allen key 18.

Note: Before restarting, check if the fastening screws 15 are

tightened well. Rotate the blade drum 13 by hand and ensure

that the planer blade does not graze.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

Clean the chip ejector 2 regularly. Use a suitable tool (e.g., a

piece of wood, compressed air, etc.) to clean a clogged chip

ejector.

f Do not reach into the saw dust ejector with your hands.

They could be injured by rotating parts.

To ensure optimum extraction of dust/chips, always work

with external dust extraction or a chip/dust bag.

External Dust Extraction (see figure C)

An extraction hose (Ø 35 mm) 19 (accessory), can be at-

tached on either side of the chip ejector.

Connect the vacuum hose 19 to a vacuum cleaner (accesso-

ry). An overview for connecting to various vacuum cleaners

can be found at the end of this manual.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Integrated Dust Extraction (see figure C)

A chip/dust bag (accessory) 20 can be used for smaller jobs.

Insert the sleeve of the chip/dust bag firmly into the chip ejec-

tor 2. Empty the chip/dust bag 20 at regulary intervals to

maintain optimum dust collection.

Choice of Chip Ejector Side

With the selector lever 9, the chip ejector 2 can be switched

to right or left. Always press the selector lever 9 until it engag-

es in the end position. The selected ejection direction is indi-

cated by an arrow symbol on the selector lever 9.

Operation

Operating Modes

Adjusting the Planing Depth

With the adjustment knob 1, the planing depth can be adjust-

ed variably from 0–4.0 mm using the planing depth scale 4

(scale graduation = 0.1 mm).

Park Rest (see figure G)

The park rest 28 allows the machine to be set down directly

after operation, without danger of damaging the working sur-

face or the planer blade. While planing, the park rest 28 is tilt-

ed upwards thus enabling full contact of the rear part of the

planer base plate 10.

Starting Operation

f Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Switching On and Off

To start the machine, first push the lock-off button for the

On/Off switch 5 and then press the On/Off switch 6 and keep

it pressed.

To switch off the machine, release the On/Off switch 6.

Note: For safety reasons, the On/Off switch 6 cannot be

locked; it must remain pressed during the entire operation.

OBJ_BUCH-633-004.book Page 14 Wednesday, October 12, 2011 11:07 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GHO 40-82 C Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GHO 40-82 C Professional Manual

Product: