Manual Bosch GHO 18 V-LI Professional (page 16 of 199) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

593161

Zoom out

Zoom in

1/199

16 | English

1 609 92A 0KP | (13.5.14) Bosch Power Tools

 Do not reach into the saw dust ejector with your hands.

They could be injured by rotating parts.

To ensure optimum extraction of dust/chips, always work

with external dust extraction or a chip/dust bag.

External Dust Extraction (see figure E)

An extraction hose (Ø 35 mm) 19 (accessory), can be at-

tached on either side of the chip ejector.

Connect the vacuum hose 19 to a vacuum cleaner (accesso-

ry). An overview for connecting to various vacuum cleaners

can be found at the end of this manual.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Integrated Dust Extraction (see figure E)

A chip/dust bag (accessory) 20 can be used for smaller jobs.

Insert the sleeve of the chip/dust bag firmly into the chip ejec-

tor 1. Empty the chip/dust bag 20 at regulary intervals to

maintain optimum dust collection.

Choice of Chip Ejector Side

With the selector lever 4, the chip ejector 1 can be switched

to right or left. Always press the selector lever 4 until it engag-

es in the end position. The selected ejection direction is indi-

cated by an arrow symbol on the selector lever 4.

Operation

Operating Modes

Adjusting the Planing Depth

With the adjustment knob 2, the planing depth can be adjust-

ed variably from 0–1.6 mm using the planing depth scale 3.

Starting Operation

Inserting the battery

Insert the charged battery 7 into the battery port until it can

be felt to engage and is seated flush.

Switching On and Off

To start the machine, first push the lock-off button for the

On/Off switch 5 and then press the On/Off switch 6 and keep

it pressed.

To switch off the machine, release the On/Off switch 6.

Note: For safety reasons, the On/Off switch 6 cannot be

locked; it must remain pressed during the entire operation.

To save energy, only switch the power tool on when using it.

Run-on Brake

An integrated run-on brake reduces after-running of the blade

shaft after switching off the machine.

Protection Against Deep Discharging

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Working Advice

Planing

Set the required planing depth and place the front part of the

planer base plate 10 against the workpiece.

 Apply the machine to the workpiece only when

switched on. Otherwise there is danger of kickback when

the cutting tool jams in the workpiece.

Switch the machine on and guide the machine with even feed

over the surface to be planed.

To achieve high-grade surfaces, work only with low feed and

apply pressure on the centre of the planer base plate.

When machining hard materials (e.g. hardwood) as well as

when utilising the maximum planer width, set only low planing

depths and reduce planer feed, as required.

Excessive feed reduces the surface quality and can lead to

rapid clogging of the chip ejector.

Only sharp blades achieve good cutting capacity and give the

machine longer life.

Beveling Edges (see figure F)

The V-grooves in the front planer base plate allow quick and

easy beveling of workpiece edges. Depending on required

bevel width, use the corresponding V-groove. For this, place

the planer with the V-groove onto the edge of the workpiece

and guide it along the edge.

Planing with Parallel/Beveling Guide (see figure G–I)

Mount the parallel guide 21 or beveling guide 25 to the ma-

chine using the corresponding fastening bolt 24. Depending

on the application, mount the rebating depth stop 28 with fas-

tening bolt 27 to the machine.

Loosen the locking nut 23 and adjust the requested rebating

width on the scale 22. Tighten the locking nut 23 again.

Adjust the requested rebating depth accordingly with the re-

bating depth stop 28.

Carry out the planing procedure several times until the re-

quested rebating depth is reached. Guide the planer applying

sideward supporting pressure.

Beveling with the Beveling Guide

When beveling rebates and

surfaces, adjust the required

slope angle with the angle ad-

justment 26.

Groove to be used Dimension a

(mm)

none 0–2.5

small 1.5–4.0

medium 2.0–4.5

large 3.0–5.5

OBJ_BUCH-1520-004.book Page 16 Tuesday, May 13, 2014 2:26 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GHO 18 V-LI Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GHO 18 V-LI Professional Manual

Product: