Manual Bosch GHO 18 V-LI Professional (page 15 of 199) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

593161

Zoom out

Zoom in

1/199

English | 15

Bosch Power Tools 1 609 92A 0KP | (13.5.14)

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 25.03.2014

Assembly

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

Battery Charging (see figure A)

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium-ion battery of your power tool.

Note: The battery supplied is partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

To remove the battery 7 press the unlocking buttons 8 and

pull out the battery downwards. Do not exert any force.

The Hex key 12 required for replacement of the planer blade is

located inside the machine and should always be stored there.

Observe the notes for disposal.

Battery Charge-control Indication (see figure B)

The three green LEDs of the battery charge-control indicator

14 indicate the charge condition of the battery 7. For safety

reasons, it is only possible to check the status of the charge

condition when the machine is at a standstill.

Press button 13 to indicate the charge condition. This is also

possible when the battery 7 is removed.

When no LED lights up after pushing button 13, then the bat-

tery is defective and must be replaced.

Changing the Tool

 Be cautious when replacing the planer blades. Do not

grasp the planer blades by the cutting edges. Possible

danger of injury due to the sharp cutting edges of the plan-

er blades.

Use only original Bosch carbide blades (TC).

The carbide blade (TC) has 2 cutting edges and can be re-

versed. When both cutting edges are dull, the planer blade 18

must be replaced. The carbide blade (TC) may not be resharp-

ened.

Disassembling the Planer Blade(s) (see figure C)

To reverse or replace the planer blade 18, rotate the blade

drum 15 until it is parallel to the planer base plate 10.

 Loosen the two fastening screws 17 with the Hex key 12

by approx. 1–2turns.

 If necessary, loosen the clamping element 16 by giving it

a light blow with a suitable tool (e.g. a wooden wedge).

 Push the planer blade 18 sidewards out of the blade

drum 15 with a piece of wood.

Assembling the Planer Blade(s) (see figure D)

The guide groove of the planer blade always ensures continu-

ous height adjustment when replacing or reversing it.

If required, clean the blade seat in the clamping element 16

and the planer blade 18.

When assembling the planer blade, ensure that it is seated

properly in the blade holder of the clamping element 16 and

aligned flush at the side edge of the rear planer base plate 10.

Afterwards tighten the 2 fastening screws 17 again with the

Hex key 12.

Note: Before restarting, check if the fastening screws 17 are

tightened well. Rotate the blade drum 15 by hand and ensure

that the planer blade does not graze.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

Clean the chip ejector 1 regularly. Use a suitable tool (e.g., a

piece of wood, compressed air, etc.) to clean a clogged chip

ejector.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

LED Capacity

Continuous lighting 3 x green ≥ 2/3

Continuous lighting 2 x green ≥ 1/3

Continuous lighting 1 x green <1/3

Flashing light 1 x green Reserve

OBJ_BUCH-1520-004.book Page 15 Tuesday, May 13, 2014 2:26 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GHO 18 V-LI Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GHO 18 V-LI Professional Manual

Product: