78670
20
Zoom out
Zoom in
Previous page
1/122
Next page
1 609 929 M67 | (12.11.07) Bosch Power Tools
20 | English
Assembly
Battery Charging
A battery that is new or has not been used for a
longer period does not develop its full capacity
until after approx. 5 charging/discharging cycles.
To remove the battery 5 press the unlocking but-
tons 6 and pull out the battery downwards. Do
not exert any force.
The battery is equipped with a NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A long
battery service life is achieved in this manner.
A significantly reduced working period after
charging indicates that the battery is used and
must be replaced.
Observe the notes for disposal.
Changing the Tool (see figure A)
f Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
GDR 9,6 V/GDR 12 V/GDR 14,4 V/GDR 18 V:
Inserting
Pull the locking sleeve 2 forward, push the insert
tool to the stop into the tool holder 1 and release
the locking sleeve 2 to lock the insert tool.
For quick changing of bits, it is recommended to
use a universal bit holder 11.
Removing
Pull the locking sleeve 2 forward and remove the
insert tool.
GDS 12 V/GDS 14,4 V/GDS 18 V:
f When working with an application tool, pay
attention that the application tool is firmly
seated on the tool holder. When the applica-
tion tool is not firmly connected with the tool
holder, it can come loose again and not be
controlled.
Slide the application tool onto the square drive
of the tool holder 1.
Operation
Method of Operation
The tool holder 1 with the tool is driven by an
electric motor via a gear and impact mechanism.
The working procedure is divided into two phas-
es:
Screwing in and tightening (impact mechanism
in action).
The impact mechanism is activated as soon as
the screwed connection runs tight and thus load
is put on the motor. In this instance, the impact
mechanism converts the power of the motor to
steady rotary impacts. When loosening screws or
nuts, the process is reversed.
Starting Operation
Inserting the Battery
f Use only original Bosch O-pack batteries
with the voltage given on the type plate of
your machine. The use of other batteries can
lead to injuries and danger of fire.
Set the rotational direction switch 8 to the centre
position in order to avoid unintentional starting.
Insert the charged battery 5 into the handle so
that it can be felt to engage and faces flush
against the handle.
Reversing the Rotational Direction
(see figure B)
The rotational direction switch 8 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 9 actuated.
Right rotation: For driving in screws and tighten-
ing nuts, press the rotational direction switch 8
through to the left stop.
Left Rotation: For loosening and unscrewing
screws and nuts, press the rotational direction
switch 8 through to the right stop.
Switching On and Off
To start the machine, press the On/Off switch 9
and keep it depressed.
To switch off the machine, release the On/Off
switch 9.
OBJ_BUCH-595-001.book Page 20 Monday, November 12, 2007 4:15 PM
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GDS 14,4 V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GDS 14,4 V in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info