591911
11
Zoom out
Zoom in
Previous page
1/128
Next page
English | 11
Bosch Power Tools 1 609 92A 0PW | (31.10.14)
8 Lower screw of drilling-angle adjustment
9 Bottom plate
10 Rack
11 Clamping nut of drilling-angle adjustment
12 Feed pinion
13 Parking brake
14 Spirit level for vertical alignment (GDB 180 WE)
15 Spirit level for horizontal alignment (GDB 180 WE)
16 Brickwork anchor/concrete anchor*
17 Quick-clamping spindle*
18 Wing nut*
19 Tension spring of water collection ring*
20 Sliding guides
21 Hex nut of sliding guides (10 pcs)
22 Threaded pin of sliding guides (10 pcs)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” complies with all applicable
provisions of the directive 2006/42/EC including its amend-
ments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 14.10.2014
Assembly
Mounting the Drill Stand
Erecting the Drilling Column
Put the drilling column 4 in a vertical position. Insert the lower
screw 8 (see illustration on the graphics page). Tighten the
lower screw 8 and the upper screw 5 using an open-end span-
ner (size 17 mm). Tighten the clamping nut 11 using an open-
end spanner (size 24 mm).
Star Handle
Screw the three handle bars of the star handle 1 all the way in-
to the central hub of the star handle.
The star handle 1 serves as the feed crank during drilling.
To drill, slide the star handle left or right, as required, all the
way onto the feed pinion 12. Pull the star handle off firmly to
remove it.
Feed Lock with Parking Brake
Before first-time use, screw the parking brake 13 into the free
threaded hole underneath the feed pinion 12.
Lock the feed when performing any work on the drill stand,
during work breaks and when not using the drill stand. To do
so, turn on the parking brake 13.
To drill, loosen the parking brake 13 until the star handle 1 is
easy to move. When doing so, hold the star handle in place in
order to prevent the drill from sliding down in an uncontrolled
manner.
Mounting the Diamond Drill (see figure A)
Remove the auxiliary handle of your drill (see operating in-
structions of the drill).
Ensure that the parking brake 13 is on.
Loosen the screw 2 on the drill fixture using an open-end
spanner (size 13 mm). Insert the drill with the collar from
above all the way into the drill fixture 3.
Turn the drill in the drill fixture so that all switches are easy to
reach and the dust extraction/water cooling connection on
the drill does not interfere with drilling. Tighten the screw 2
using the open-end spanner (size 13 mm).
Slide the star handle 1 right or left onto the feed pinion 12 in
order to drill.
Check the tight seating of the drill in the drill fixture.
To remove the drill from the drill stand, complete the steps in
reverse order.
Fastening the Drill Stand
Note: Fasten the drill stand free from play to prevent jamming
of the core bit and the tearing out of segments.
Depending on the type and condition of the surface, fasten the
drill stand at the planned bore hole using anchors or vacuum.
Positioning the Drill Stand before Fastening
Mark the centre of the bore hole you want to drill on the surface.
Mark the outer dimensions of the core bit you want to drill with,
using the centre of the bore hole as the centre of the bit.
Drill stand for diamond drills GCR 180
Article number
3 601 A90 100
Dimensions
–Height
–Width
–Depth
mm
mm
mm
767
205
423.5
Diameter of drill fixture
mm 60
Dimensions of core bit, max.
–Diameter
Diameter with water collec-
tion ring
–Length
mm
mm
mm
180
132
530
Drill stroke, max.
mm 514
Working length, max.
mm 455
Weight according to
EPTA-Procedure 01/2003
kg 9.5
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-2243-001.book Page 11 Friday, October 31, 2014 12:11 PM
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GCR 180 Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GCR 180 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info