786454

Bosch GCO 14-24 J Manual

18
Zoom out
Zoom in
Previous page
1/255
Next page
18 | English
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
uAvoid starting the power tool unintentionally. The
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
Carefully remove all parts included in the delivery from their
packaging.
Remove all packing material from the power tool and the ac-
cessories provided.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Cut-off grinder with cutting disc fitted
– Hex key (12)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Stationary or flexible mounting
uTo ensure safe handling, the power tool must be
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure A)
– Use suitable screw fasteners to secure the power tool to
the work surface. Use the holes (11) to do this.
Flexible installation (not recommended)
In exceptional circumstances, if it is not possible to securely
mount the power tool on a work surface, you can improvise
by placing the feet of the base plate (13) on an appropriate
base (e.g. workbench, flat ground, etc.), without screwing
down the power tool.
Changing the Cutting Disc (seefiguresB1−B2)
uPull the plug out of the socket before carrying out any
work on the power tool.
uDo not activate the spindle lock (5) while the tool
spindle (22) is moving. The power tool may become
damaged if you do this.
uDo not touch the cutting disc after use until it has
cooled. The cutting disc becomes very hot during use.
Only use cutting discs that match the specifications given in
this operating manual and that have been tested and marked
in accordance with EN 12413.
Use any intermediate layers provided with the cutting disc.
Place unused cutting discs in an enclosed container or their
original packaging. Store the cutting discs lying flat.
Removing the cutting disc
– Bring the power tool into the work position.
– Swivel the retracting blade guard (4) backwards as far as
possible.
– Turn the hexagon screw (25) using the hex key (12)
provided while pressing the spindle lock (5) until it en-
gages.
– Hold the spindle lock down and unscrew the hexagon
screw (25).
– Remove the washer (24) and the clamping flange (23).
– Remove the cutting disc (6).
Fitting the cutting disc
If required, clean all the parts you want to fit before installing
them.
– Place the new cutting disc on the tool spindle (22) such
that the sticker points away from the tool arm.
– Fit the clamping flange (23), the washer (24) and the
hexagon screw (25). Press the spindle lock (5) until it en-
gages and retighten the hexagon screw (25) by turning it
clockwise. (Tightening torque approx. 18–20Nm)
– Slowly guide the retracting blade guard (4) all the way
down until the cutting disc is completely covered.
– Make sure that the retracting blade guard (4) is working
properly.
After fitting the cutting disc, check that the cutting disc is fit-
ted correctly and can turn freely before switching on the
power tool.
– Make sure that the cutting disc does not brush against the
retracting blade guard (4), the fixed protective guard
(20) or any other parts.
– Put the power tool into operation for approx. 30 seconds.
If there is substantial vibration, switch the power tool off
immediately, remove the cutting disc and then refit it.
Operation
uPull the plug out of the socket before carrying out any
work on the power tool.
Transport Safety Lock (see figure C)
The transport safety lock (17) makes it easier to handle the
power tool when transporting it to various working locations.
Unlocking the power tool (work position)
– Press the tool arm down slightly by the handle (3) to re-
lease the transport safety lock (17).
– Pull the transport safety lock (17) all the way out.
1 609 92A 7ND | (26.04.2022) Bosch Power Tools
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GCO 14-24 J at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GCO 14-24 J in the language / languages: All languages as an attachment in your email.

The manual is 10.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info