Manual Bosch gbh 36 v li compact (page 25 of 317) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

388877

Zoom out

Zoom in

1/317

English | 25

Bosch Power Tools 1 619 929 797 | (3.2.09)

Adjusting the Drilling Depth on the Dust Ex-

traction Attachment (see figure H)

The required drilling depth X can also be adjust-

ed when the dust extraction attachment is

mounted.

– Insert the SDS-plus drilling tool to the stop

into the SDS-plus tool holder 2. Otherwise,

the movability of the SDS-plus drilling tool

can lead to incorrect adjustment of the drill-

ing depth.

– Loosen the wing bolt 24 on the dust extrac-

tion attachment.

– Without switching the power tool on, apply it

firmly to the drilling location. The SDS-plus

drilling tool must face against the surface.

– Position the the guide pipe 25 of the dust ex-

traction attachment in its holding fixture in

such a manner that the head of the dust ex-

traction attachment faces against the surface

to be drilled. Do not slide the guide pipe 25

further over the telescopic pipe 23 of the

dust extraction attachment than required, so

that as much as possible of the scale 23 on

the telescopic pipe remains visible.

– Retighten the wing bolt 24 again. Loosen the

clamping screw 21 on the depth stop of the

dust extraction attachment.

– Move the depth stop 22 on the telescopic

pipe 23 in such a manner that the

clearance X shown in the figure corresponds

with the required drilling depth.

– Tighten the clamping screw 21 in this posi-

tion.

Operation

Starting Operation

Inserting the Battery

f Use only original Bosch lithium ion batter-

ies with the voltage listed on the nameplate

of your power tool. Using other batteries can

lead to injuries and pose a fire hazard.

– Set the rotational direction switch 6 to the

centre position to protect the power tool

against accidental starting.

– Insert the charged battery 11 from the front

into the base of the power tool. Push the bat-

tery completely into the base until the red

stripe can no longer be seen and the battery

is securely locked.

Setting the Operating Mode

With the selector switch for drilling/hammer

drilling 8, the operating mode of the machine is

selected.

Note: Change the operating mode only when the

machine is switched off! Otherwise, the ma-

chine can be damaged.

– To change the operating mode, turn the se-

lector switch for “drilling/hammer drilling” 8

to the requested position.

Reversing the Rotational Direction

(see figure I)

The rotational direction switch 6 is used to re-

verse the rotational direction of the machine.

However, this is not possible with the On/Off

switch 7 actuated.

Right rotation: Push the rotational direction

switch 6 left to the stop.

Left rotation: Push the rotational direction

switch 6 right to the stop.

For hammer drilling and drilling, always set the

direction of rotation to right rotation.

Switching On and Off

–To start the machine, press the On/Off

switch 7.

When starting the machine for the first time, a

starting delay is possible, as the electronic sys-

tem of the power tool has to configure itself

first.

–To switch off the machine, release the

On/Off switch 7.

Position for hammer drilling in con-

crete or stone

Position for drilling without impact

in wood, metal, ceramic and plastic

as well as for screwdriving

OBJ_BUCH-518-002.book Page 25 Tuesday, February 3, 2009 12:02 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gbh 36 v li compact in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch gbh 36 v li compact Manual

Product: