786259

Bosch GBH 18V-34 CF Manual

24
Zoom out
Zoom in
Previous page
1/337
Next page
24 | English
Working mode(25) indic-
ator Functions
lights up Favourite working mode: Individual configuration via smartphone app
The following settings are pre-programmed:
– "Hammer drilling" operating mode (Electronic Precision Control soft start): Fastest pos-
sible run-up up to maximum power
– Rapid Shut-off (KickBack Control) active
– "Chiselling" operating mode (Adaptive Speed Control soft start): Deactivated, fastest pos-
sible run-up up to maximum power
Connectivity functions
In conjunction with the Bluetooth® Low Energy Module
GCY42, the following connectivity functions are available
for the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy ModuleGCY42.
Practical Advice
uWith the Bluetooth® Low Energy Module GCY 42, the
power tool is equipped with a radio interface. Local
operating restrictions, e.g. in aircraft or hospitals,
must be observed.
uIn areas where the Bluetooth® wireless technology is
not allowed to be used, the Bluetooth® Low Energy
Module GCY42 and the button cell must be removed.
Note: The cover(13) can only be securely closed if the
Bluetooth® Low Energy Module GCY42 and the button cell
are situated in the power tool.
– To deactivate the Bluetooth® Low Energy Module
GCY42, rotate the button cell or place means of insula-
tion between the button cell and Bluetooth® Low Energy
Module GCY42.
– Close the cover(13) to prevent dirt from getting in.
Setting the drilling depth (see figure J)
You can use the depth stop (17) to set the required drilling
depthX.
– Press the button for depth stop adjustment (15) and in-
sert the depth stop into the auxiliary handle (16).
The fluting on the depth stop (17) must face downwards.
– Insert the SDS-plus application tool into the SDS-plus tool
holder (3) to the stop. Otherwise, the movability of the
SDS-plus drilling tool can lead to incorrect adjustment of
the drilling depth.
– Pull the depth stop far enough out that the distance
between the drill bit tip and the edge of the depth stop
corresponds to the required drilling depth X.
Overload clutch
uIf the application tool jams or snags, the power trans-
mission to the drill spindle will be interrupted. Always
hold the power tool firmly with both hands to with-
stand the forces this may create and adopt a position
with stable footing.
uSwitch the power tool off immediately and remove the
application tool if the power tool becomes blocked.
Switching on when the drilling tool is blocked may
cause high torque reactions.
Rapid shut-off (KickBack Control)
The rapid shut-off function (KickBack
Control) gives the user greater control
over the power tool and offers them bet-
ter protection than power tools that do
not have Kickback Control. If the power
tool suddenly and unforeseeably rotates
around the drilling axis, it will switch off,
the rapid shut-off indicator (24) will light
up red and the worklight (14) will flash.
When rapid shut-off is activated, the
status indicator(27) flashes red.
– To switch the tool back on, release the on/off switch
(11) and then press it again.
Electronic Precision Control (EPC)
EPC assists you when drilling and when working with impact
in sensitive materials by ensuring slow start-up of the operat-
ing speed for precise working.
Adaptive Speed Control in "Chiselling" Operating Mode
For better control and precise position-
ing, the power tool starts at a low speed
and then increases to the set speed.
Adapted Speed Control is started up
automatically when the power tool is
switched on.
Vibration damping
The integrated vibration damping function re-
duces the generated vibration.
uDo not continue to use the power tool if the damping
element is damaged.
Maintenance and Service
Maintenance and Cleaning
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
1 609 92A 7SJ | (23.06.2022) Bosch Power Tools
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GBH 18V-34 CF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBH 18V-34 CF in the language / languages: All languages as an attachment in your email.

The manual is 7.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info