786485

Bosch GAS 35 H AFC Manual

24
Zoom out
Zoom in
Previous page
1/313
Next page
24 | English
Vacuuming up liquids
– To switch on the dust extractor, set the mode selector
switch(7) to the "extraction" symbol.
The dust extractor is equipped with fill level sensors (40).
The dust extractor shuts down if the maximum fill level has
been reached. Set the mode selector switch (7) to the
"switch off" symbol.
Note: When extracting non-conductive liquids (e.g. drilling
emulsion, oils and fats), the dust extractor will not switch off
when the container is full. The fill level must be constantly
monitored and the container emptied in good time.
If the acoustic warning signal sounds during wet extraction,
the operating reliability of the dust extractor is not affected.
No measures to rectify the fault are necessary.
– To switch off the dust extractor, set the mode selector
switch(7) to the "switch off" symbol.
– To transport the dust extractor, screw the sealing plug(2)
onto the hose adapter(3).
– Empty the container(1).
To prevent mould growth after wet extraction:
– Remove the flat-pleated filter(28) and leave this to dry
thoroughly.
– Remove the top part of the dust extractor(12), open the
filter cover(39) and leave both elements to dry thor-
oughly.
Automatic filter cleaning (see figureH)
When automatic filter cleaning (AFC) is active, the flat-
pleated filter(28) is cleaned every 15 seconds using blasts
of air (pulsating noise).
The filter cleaning function should be activated at the very
latest when the suction power is no longer sufficient.
Regular use of the filter cleaning function will increase the
service life of the filter.
In order to achieve an optimum filter service life, deactivate
the automatic filter cleaning function only in exceptional
cases, e.g. when vacuuming pure liquids or using a safety fil-
ter bag.
A flat-pleated filter with surface dirt is still fully functional. It
is not necessary to clean the flat-pleated filter manually by
shaking or blowing it out; this may even damage the filter.
Note: The automatic filter cleaning function is switched on
by default when the dust extractor leaves the factory.
It is only possible to switch the automatic filter function on or
off when the tool is switched on.
–Deactivating AFC
Press the AFC button(9).
The control LED(37) will go out.
–Activating AFC
Press the AFC button(9).
The control LED(37) will light up green.
Maintenance and Service
Maintenance and Cleaning
uPull the plug out of the socket before cleaning or per-
forming maintenance on the vacuum cleaner, making
tool adjustments, changing accessories or putting
away the vacuum cleaner. This safety measure prevents
the vacuum cleaner from being started accidentally.
uTo ensure safe and efficient operation, always keep
the dust extractor and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
uWear a protective mask of protection class FFP2 or
higher and disposable protective suit according to the
relevant provisions when carrying out maintenance
and cleaning of the dust extractor. Maintenance and
cleaning may only be carried out by persons with
proof of expertise.
The housing of the dust extractor must be thoroughly vacu-
umed and wiped clean with a damp cloth, or treated with
sealant, before the dust extractor can be removed from the
hazardous area. All dust extractor parts must be considered
to be contaminated when taken from the hazardous area, ap-
propriate precautions must be taken. All parts not suffi-
ciently cleaned during maintenance/repair must be disposed
of (in impermeable bags).
For the user to carry out maintenance, the dust extractor
needs to be disassembled, cleaned and maintained as far as
this is possible without endangering maintenance personnel
or other persons. Before disassembly, the dust extractor
should be cleaned to prevent any potential hazards. The pro-
cesses described in the Assembly chapter form part of the
maintenance routine. The room/enclosure in which the dust
extractor is disassembled should be well ventilated. Wear
personal protective equipment while carrying out mainten-
ance.
After completing maintenance, the maintenance area should
be cleaned.
A technical inspection must be carried out at least once a
year by the manufacturer or someone who has been trained,
e.g. to check for filter damage and to check that the dust ex-
tractor is tight and that the control unit is functioning cor-
rectly.
In addition to this, the effectiveness of the filter must be in-
spected at least annually in accordance with
EN60335-2-69, 22.AA.201.2.
National requirements may also necessitate more frequent
inspection.
If the filter is no longer deemed effective, it must be replaced
and the test must be repeated.
Removing/changing the flat-pleated filter (see figures
I1–I2)
The suction power is dependent on the condition of the fil-
ter. Therefore, the filter should be cleaned regularly.
1 609 92A 7Z8 | (23.06.2022) Bosch Power Tools
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GAS 35 H AFC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GAS 35 H AFC in the language / languages: All languages as an attachment in your email.

The manual is 8.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info