Manual Bosch GAS 18V-10 L (page 19 of 221) (All languages)

786180

Zoom out

Zoom in

1/221

English | 19

Switching On and Off

To switch on the dust extractor, briefly press the on/off

button(3).

To switch off the dust extractor, press the on/off button(3)

again.

For safety reasons, the dust extractor does not switch on if

the on/off button(3) is held down for longer than five

seconds.

Dry Vacuuming

Extracting dust that accumulates from working power

tools (seefigureG)

uThere must be a sufficient air exchange rate (L) in the

room when the exhaust air comes back into the room.

Be aware of the corresponding national regulations.

– Fit the dust extraction adapter(14) or the curved

nozzle(15) (see "Fitting the extraction adapter or curved

nozzle (seefigureD)", page18).

– Insert the extraction adapter(14) or the curved

nozzle(15) into the power tool's dust extraction outlet.

Only when using the dust extraction adapter(14):

Note: When working with power tools that have a low air

feed into the vacuum hose (e.g. jigsaws, sanders, etc.), the

false air intake(32) of the dust extraction adapter(14) must

be opened. This will improve the total output of the dust ex-

tractor and the power tool. To do this, turn the ring above

the false air intake(32) until the opening is at its maximum

size.

Wet Vacuuming

uDo not use the vacuum cleaner to vacuum combustible

or explosive liquids, such as petrol, oil, alcohol or

solvents. Do not vacuum hot, burning or explosive

dust. Do not operate the vacuum cleaner in areas sub-

ject to explosion hazards. Dust, vapours and liquids can

ignite or explode.

Before wet vacuuming:

– Empty the container (1).

– Clean the filter(33) and fit it back into the dust ex-

tractor(see "Cleaning/replacing filters (see figures I1–

I2)", page19).

The dust extractor is equipped with a float(34). Extraction

is stopped when the maximum filling level is reached.

After wet vacuuming, always:

– Empty the container (1).

– Empty the water from the filter (33).

To prevent mould growth after wet vacuuming:

– Remove the dust extractor lid (5) and leave it to dry thor-

oughly.

– Remove the filter (33) and also leave this to dry thor-

oughly (see "Cleaning/replacing filters (see figures I1–

I2)", page19).

Maintenance and Servicing

Maintenance and Cleaning

uRemove the battery before cleaning or performing

maintenance on the dust extractor, making tool ad-

justments, changing accessories or placing the dust

extractor in storage. This safety measure prevents the

dust extractor from being started accidentally.

uTo ensure safe and efficient operation, always keep

the dust extractor and the ventilation slots clean.

For the user to carry out maintenance, the dust extractor

needs to be disassembled, cleaned and maintained as far as

this is possible without endangering maintenance personnel

or other persons. Before disassembly, the dust extractor

should be cleaned to prevent any potential hazards. The

room/enclosure in which the dust extractor is disassembled

should be well ventilated. Wear personal protective equip-

ment while carrying out maintenance. After completing

maintenance, the maintenance area should be cleaned.

An inspection regarding the dust extraction capability must

be carried out at least once a year by the manufacturer or

someone who has been trained, e.g. to check for filter dam-

age, that the dust extractor is tight and that the control unit

is functioning correctly.

Class L dust extractors which were located in dirty environ-

ments should have their exteriors, as well as all their com-

ponents, cleaned or treated with sealant. When performing

maintenance and repair work, all dirty parts that cannot be

cleaned satisfactorily must be disposed of. Such parts must

be disposed of in impermeable bags in accordance with the

valid provisions for disposing of such waste.

– Clean the housing of the dust extractor occasionally with

a damp cloth.

– Clean dirty charging pins using a dry cloth.

Cleaning the container (see figures H1–H2)

Clean the container (1) after each use in order to ensure that

the dust extractor continues to perform optimally.

– Open the catches (2) and remove the dust extractor lid

(5).

– Shake out the container (1) over a suitable waste bin.

– If necessary, clean the container with a damp cloth.

Clean the filter if required (see "Cleaning/replacing filters

(see figures I1–I2)", page19).

– Replace the dust extractor lid (5) and close the catches

(2).

Cleaning/replacing filters (see figures I1–I2)

Suction power is dependent on the condition of the filter.

Therefore, the filter should be cleaned regularly.

Replace any damaged filters immediately.

– Open the catches(2) and remove the dust extractor lid

(5).

– Turn the filter(33) as far as it will go in the direction of ro-

tation and remove it from the filter bracket(35).

– If the filter is dry:

Tap the filter(33) on the side of a suitable waste bin.

Bosch Power Tools 1 609 92A 7MV | (12.05.2022)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GAS 18V-10 L in the language / languages: All languages as an attachment in your email.

The manual is 6.5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GAS 18V-10 L Manual

Product: