786514

Bosch GAM 270 MFL Manual

20
Zoom out
Zoom in
Previous page
1/331
Next page
20 | English
Rotating the Display
When you rotate the measuring tool 180°, the display will also rotate auto-
matically to make the displayed value easier to read.
"Normal measuring" Operating Mode
After switching on, the measuring tool is always in "normal measuring" oper-
ating mode.
In "Normal Measuring" mode, angle measurement and grade measurement
are carried out simultaneously.
Measuring Angles (seefiguresC–D)
Place the fold-out leg (1) and the base leg(4) flat on the surfaces adjacent
to the angle. The displayed measured value(g) corresponds with the in-
terior anglew between the base leg and the fold-out leg.
This measured value is shown on the display(7) until you change the angle
between fold-out leg(1) and base leg(4).
Transferring Angles (seefigureE)
Measure the angle to be transferred by placing the fold-out leg and base leg
on the target angle.
The position of the legs can be locked mechanically by tightening the locking
wheel(3). The displayed value is not saved.
Place the measuring tool in the required position against the workpiece. Use
the legs as a straight edge to transfer the angle.
Storing the Measured Value
Press the Hold(17)button to store (H) the current measured value(g).
The indicator(a) flashes in the display for confirmation. The currently dis-
played value is frozen and will not change even when the leg is moved. If you
press the memory buttonHold again, the indicator(a) will be shown per-
manently on the display. The displayed value will change depending on the
leg movement. The previously frozen value is now saved in the background.
If the memory buttonHold(17) is pressed again, the previously saved value
is displayed and the indicator(a) flashes.
To delete the contents of the memory, briefly press the on/off button(14).
To be able to save a new value, a previously saved value has to be deleted.
Saved values cannot be overwritten.
The held value is saved even when the measuring tool is switched off (manu-
ally or automatically). However, it is deleted when changing batteries or
when the batteries are empty.
Measuring with Leg Extension (seefiguresG–H)
The leg extension(21) makes it possible to measure angles when the con-
tact surface is shorter than the fold-out leg(1).
Place the base leg(4) and the leg extension flat on the surfaces to be meas-
ured.
The measured value of the anglew between the base leg and fold-out leg is
indicated in the display. The required anglev between the base leg and leg
extension is calculated as follows:
v=180° – w
v
v
w
"Simple Mitre" Operating Mode
The "Simple mitre" measurement is used to calculate the cutting angle MTR
when two workpieces with the same mitre have to form any outer angle x°
smaller than 180° (e.g. for skirting boards, banister columns or picture
frames).
The "simple mitre" operating mode is activated by pressing the
buttonMTR1(15). The displayed value is always used for the calculation of
the MTR. If a saved value is being displayed (indicator(a) flashes), the cal-
culation will be performed with the saved value regardless of the position of
the legs.
1 609 92A 7M1 | (28.04.2022) Bosch Power Tools
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GAM 270 MFL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GAM 270 MFL in the language / languages: All languages as an attachment in your email.

The manual is 10.75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info