462319
11
Zoom out
Zoom in
Previous page
1/33
Next page
11
2.4 Setting up aiming device
The distance between the aiming device and the headlamp should
be just enough so that setting operations can also be carried out
on the headlamp from in front (about 30 cm).
The center of the lens on the aiming device should differ by less
than 3 cm from the headlamp center. The center of the lens is
identified by marks (see Fig. 2, No. 5).
In order to adjust the height of the aiming device, the hand roller ist
turned (1) and a brake is released. The brake automatically looks
in place again when the roller is released.
Fig. 4
1 control knob for height adjustment
2 rotary knob for setting the inclination measure
2.5 Aligning the aiming device with the longitudinal axis
of the vehicle
2.5.1 Vehicles with flat engine-compartment lid
By swinging the mirror arm (Fig. 1, Pos. 2) the alignment mirror
(Fig. 2, Pos. 1) is set above the head towards the operator so that
the front of the vehicle with two outer symmetrical reference
points (for example, the upper edge of the headlamps, joints in the
engine hood, etc.) are visible in it.
The aiming device is aligned on the longitudinal axis of the vehicle
so that the positioning line on the mirror touches these two outer
reference points equally (see Fig. 5).
With the mobile aiming devices (EFLE 50, 51, 60 and 61), this is
done by moving the aiming device using the wheeling handle.
The floor-rail aiming device (EFLE 52 and 62) is turned as required
with the rotary knob at the top of the support column (Fig. 3, No. 1).
Fig. 5
2.5.2 Cab-over-engine vehicles
In vehicles with vertical front section the centres of the headlights
are marked with chalk on the floor using a plumb bob. The centres
can be connected with a rail. These markings are lined up in the
adjusting mirror.
Fig. 6
2.6 Adjusting the aiming device
The setting used for aiming headlamps is the inclination value in cm
which the cut-off must have at a distance of 10 m.
This setting is given in Section 3.1, and is made before the test at
the rotary knob (Fig. 4, No. 2).
The vehicle should be loaded as specified.
3. Aiming regulations
Please observe the aiming regulations valid in your country.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch EFLE60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EFLE60 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info