766863

Bosch EasyPrune Manual

15
Zoom out
Zoom in
Previous page
1/241
Next page
English | 15
LED Capacity
Single flash, red 0 − 5%
Charging Guide
Please charge before use.
Charge-control indicator will flash red if:
– Charger is damaged
– Incorrect charger is installed
The tool has overload protection software. If the software is
activated, the tool will lock to prevent damage. To reset the
protection software, connect the charger. Before re-use, we
recommend to fully charge the tool until the charge-control
indicator is continuously green.
Operation
Unlocking (see figure B1)
Deactivate the safety lock (6) by pushing it back. The tool
will open and is now ready for use.
Locking
After usage, close the handles and engage the safety lock (6)
by pushing it forward. Always keep in locked position, when
not in use.
Gripping position (see figures B2–B4)
Grip the tool at the front, as shown. Do not grip the tool to-
wards the back of the handles or with finger(s) between the
handles.
Power-assisted cutting (see figure B)
This tool provides power-assisted cutting. It is operated like
a pair of manual secateurs and will cut in manual mode
without power-assisted cutting until a certain branch dia-
meter is reached. The tool will start power-assisted cutting
when cutting above this branch diameter by starting the in-
tegrated motor. Noise development while power-assisted
cutting is active, is normal.
Power-assist feature is only active as long as gripping force
is exerted on the handles. If no force is exerted onto the
handles, the tool stops.
Working Advice
Pruning tips (see figures C1–C10)
Never operate the tool in an awkward posture. This may
cause serious injury.
Keep your free hand away from the cutting area. Never
touch the blades. They are very sharp and you may cut
yourself.
C1 Always wear protective gloves while pruning.
C2 Never cut too close to the stem so the wound can
heal properly.
C3 Always make the cut about 8mm from the bud.
C4 The cut should slope away from the bud so the rain
can run off.
C5 If you remove an entire stem, cut back to the point
where it branched.
C6 Never push the blade of the pruner into the ground to
cut root suckers.
C7 Cut branches one by one as shown.
C8 Remove overcrowds or crossing stems.
C9 Remove thin or weak growth.
C10 Always remove dead, damaged and diseased
branches.
Troubleshooting
The following table provides common troubleshooting information. The battery-charge control indicator provides additional
information that can be used to identify a malfunction or problem.
Problem Possible Cause Corrective Measure
Tool stops while cutting Not enough pressure on handles Continue moving handles towards each other
while cutting.
Hold the tool with a firmer grip.
Blades get stuck in a thick
branch Low battery capacity
Too hard wood
Too big diameter
Wrong cutting position
Grip the upper handle only and remove the tool
by tilting the blade.
Recharge tool, if necessary.
Power-assisted cutting does not activate with LED flashing when cutting is attempted:
LED flashes red 3 times Wood being cut is too thick/hard Try cutting in a thinner area of the branch.
Bosch Power Tools F 016 L94 019 | (04.03.2020)
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch EasyPrune at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyPrune in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 4,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info