Manual Bosch EasyImpact 360 (page 13 of 77) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian)

766873

Zoom out

Zoom in

1/77

English | 13

Then turn the lower gripping end of the auxiliary handle (8)

clockwise to retighten it.

The fluting on the depth stop(9) must face downwards.

Changing the Tool

uWear protective gloves when changing tools. The drill

chuck may heat up significantly when it is used for long

periods.

Keyless chuck (see figure B)

Hold the rear sleeve (2) of the keyless chuck (3) firmly and

turn the front sleeve (1) in the rotational direction  until

the tool can be inserted. Insert the tool.

Hold the rear sleeve(2) of the keyless chuck(3) tight and

firmly turn the front sleeve(1) in rotational direction by

hand.

Screwdriving tools

You should always use a universal bit holder (12) when using

screwdriver bits (11). Only use screwdriver bits that fit the

screw head.

For screwdriving, make sure the "drilling/impact drilling" se-

lector switch (4) is always set to the "drilling" symbol.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Changing the drill chuck

uIf your power tool does not have a drill spindle locking

mechanism, you must have the drill chuck changed by an

authorised after-sales service centre forBosch power

tools.

The drill chuck must be tightened using a tight-

ening torque of approx. 30–35Nm.

Operation

Starting Operation

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Setting the rotational direction (see figureC)

The rotational direction switch (7) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (6) is being pressed.

Right rotation: To drill and to drive in screws, press the ro-

tational direction switch (7) through to the left stop.

Left rotation: To loosen and unscrew screws, press the ro-

tational direction switch (7) through to the right stop.

Setting the Operating Mode

Drilling and screwdriving

Set the selector switch (4) to the "drilling"

symbol.

Impact drilling

Set the selector switch (4) to the "impact

drilling" symbol.

The selector switch (4) clicks into place and can also be ac-

tuated when the motor is running.

Switching on/off

To start the power tool, press and hold the on/off switch

(6).

Press the lock-on button (5) to lock the on/off switch (6) in

this position.

To switch off the power tool, release the on/off switch (6);

or, if the switch is locked with the lock-on button (5), briefly

press the on/off switch (6) and then release it.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when

it is on by pressing in the on/off switch (6) to varying ex-

tents.

Applying light pressure to the on/off switch (6) results in a

low rotational speed/impact rate. Applying increasing pres-

sure to the switch increases the speed/impact rate.

Practical Advice

uPull the plug out of the socket before carrying out any

work on the power tool.

uOnly apply the power tool to the screw/nut when the

tool is switched off. Rotating tool inserts can slip off.

After working at a low speed for an extended period, you

should operate the power tool at the maximum speed for ap-

proximately three minutes without load to cool it down.

To drill into tiles, set the selector switch (4) to the "drilling"

symbol. After drilling through the tile, set the selector switch

to the "impact drilling" symbol and drill with impact.

Use carbide drill bits when working with concrete, stone and

masonry.

When drilling into metal, only use sharpened HSS drills (HSS

= high-speed steel) which are in perfect condition. The

Bosch accessory range guarantees appropriate quality.

Bosch Power Tools 1 609 92A 5Y4 | (26.11.2020)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyImpact 360 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 3,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch EasyImpact 360 Manual

Product: