Manual Bosch EasyDrill 1200 (page 14 of 187) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

708029

Zoom out

Zoom in

1/187

14 | English

Assembly

Removing the battery (see figureA)

u Use only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

the maximum performance of the battery, use the charger to

fully charge the battery before first use.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the Electronic Cell Protection (ECP). When the battery is

discharged, the power tool is switched off by means of a pro-

tective circuit: The application tool stops moving.

u Do not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

To remove the battery (9), press the release button (8) and

pull the battery downwards out of the power tool. Do not

use force to do this.

Follow the instructions on correct disposal.

Changing the Tool (see figure B)

Hold the rear sleeve (3) of the keyless chuck (1) firmly and

turn the front sleeve (2) in rotational direction ❶ until the

tool can be inserted. Insert the tool.

Hold the rear sleeve (3) of the keyless chuck (1) tight and

firmly turn the front sleeve (2) in rotational direction ➋ by

hand.

The lock will disengage again if you turn the front sleeve (2)

in the opposite direction to remove the tool.

Changing the drill chuck

Remove the securing screw (see figure C)

The keyless chuck (1) is secured with a securing screw (16)

against unintentional loosening from the drill spindle. Fully

open the keyless chuck (1) and unscrew the securing screw

(16) in rotational direction ❶. Note that the securing

screw has a left-hand thread.

Removing the drill chuck (see figure D)

Clamp a hex key (17) in the keyless chuck (1), leading with

the short shaft.

Place the power tool on a firm surface, e.g. a work bench.

Hold the power tool in place and loosen the keyless chuck

(1) by turning the hex key (17) in the rotational direction ➊.

A tightly seated keyless chuck is loosened with a light blow

on the long shaft of the hex key (17). Remove the hex key

from the keyless chuck and completely unscrew the keyless

chuck from the power tool.

Assembling the Drill Chuck (see figure E)

To assemble the keyless chuck, perform the same steps in

reverse order.

The drill chuck must be tightened using a tight-

ening torque of approx. 1.5–2.0 Nm.

Screw the securing screw (16) anticlockwise into the

opened keyless chuck (1). Always use a new securing screw

because a securing adhesive substance is applied on its

thread and is rendered ineffective after repeated use.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (10) to the middle posi-

tion to avoid unintentionally switching it on. Insert the

charged battery (9) into the handle until you feel it engage

and it is flush with the handle.

Set the rotational direction (see figureF)

The rotational direction switch (10) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (11) is being pressed.

Right rotation: To drill and to drive in screws, press the ro-

tational direction switch (10) through to the left stop.

The rotational direction indicator for right rotation

(6) lights up when the on/off switch (11) is

pressed and the motor is running.

Left Rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (10) through to the

right stop.

The rotational direction indicator for left rotation

(7) lights up when the on/off switch (11) is

pressed and the motor is running.

Preselecting the Torque

The torque presetting ring (4) can be used to preselect the

required torque in 15 stages. When the correct setting is

used, the application tool will be stopped when the screw is

driven flush into the material or once the set torque has been

1 609 92A 4Y7 | (25.09.2019) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyDrill 1200 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch EasyDrill 1200 Manual

Product: