776836

Bosch EasyCurveSander 12 Manual

14
Zoom out
Zoom in
Previous page
1/111
Next page
14 | English
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Speed preselection thumbwheel
(2) Batterya)
(3) Battery release buttona)
(4) Sanding disc
(5) Battery charge indicator
(6) On/off switch
(7) Handle (insulated gripping surface)
(8) Sanding neta)
(9) Sanding disc holder
(10) Dust extraction adapter
(11) Vacuum hosea)
(12) Rubber band
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless Disc Sander EasyCurvSander 12
Article number 3 603 JC9 0..
Rated voltage V 12
Speed preselection ●
Idle speed n0A) min-1 800–1800
Sanding pad diameter mm 38
Weight according to EPTA-
Procedure 01:2014A) kg 0.5
Recommended ambient
temperature during char-
ging
°C 0to+35
Permitted ambient temper-
ature during operationB) and
during storage
°C –20to+50
Recommended re-
chargeable batteries PBA12V…
Recommended chargers GAL 12...
A) Depends on battery in use
B) Limited performance at temperatures <0°C
Noise/Vibration Information
Noise emission values determined according
toEN62841-2-4.
Typically, the A-weighted sound pressure level of the power
tool is less than 70dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Total vibration values ah (triax vector sum) and uncertainty K
determined according to EN62841-2-4:
ah = 2.5 m/s2, K = 1.5 m/s2.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
uUse only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
uDo not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery (seefigureA)
To remove the battery(2), press the release buttons(3) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The battery charge indicator(5) on the power tool consists
of three green LEDs. It indicates the battery's state of charge
for a few seconds after the power tool is switched on and off.
LED Capacity
Continuous lighting 3x green 60–100%
1 609 92A 66A | (26.01.2021) Bosch Power Tools
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch EasyCurveSander 12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyCurveSander 12 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 12.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info