776836

Bosch EasyCurveSander 12 Manual

15
Zoom out
Zoom in
Previous page
1/111
Next page
English | 15
LED Capacity
Continuous lighting 2x green 30–60%
Continuous lighting 1x green 10–30%
Slowly flashing light 1 x green 0–10%
The three LEDs in the battery charge indicator flash
quickly when the temperature of the battery is outside
the operating temperature range of -30 to +70 °C and/or
the overload protection has been triggered.
Selecting a sanding net
Select sanding nets with a grit suitable for how much material you want to remove. Bosch sanding nets are suitable for paint
and wood.
Use Application Grit Colour of
the stripe
on the
sanding
net
Remove
(coarse sand-
ing)
– Coarse sanding work with a
high material removal rate
– Removing old paint
– Sanding down old paint, varnish and filler
– Removing thin paint
– Pre-sanding rough, unplaned surfaces
Coarse/
P80 Orange
Prepare
(intermediate
sanding)
– Light sanding
– Abrading surfaces for further
processing later on
– Sanding uneven surfaces to make them
even
– Removing marks left by coarse sanding
– Repairing surfaces before applying paint or
varnish
Medium/
P180 Yellow
Finish – Intermediate paint sanding
– Abrading flaws in the paintwork
– Removing fibres from the surface
– Fine sanding before staining
– Abrading primer before painting
Very fine/
P320 Green
Changing the Sanding net (see figure B)
Note: Always sand with sanding nets attached.
To remove the sanding net(8), lift it from the side and pull it
from the sanding disc(4).
Remove dirt and dust from the sanding disc(4), e.g.with a
paintbrush or vacuum, before attaching a new sanding net.
The surface of the sanding disc(4) is fitted with a hook-and-
loop fastening, allowing sanding nets with a similar backing
to be secured quickly and easily.
Press the sanding net(8) firmly against the underside of the
sanding disc(4).
Note: Sanding nets must be positioned correctly in order to
ensure low vibration of the power tool during operation.
Changing the sanding disc (see figure C)
Note: Replace damaged sanding discs (4) immediately.
Remove the battery from the power tool.
Remove the sanding net or polishing sponge.
Pull the sanding disc (4) out of the sanding disc holder (9).
Position the new sanding disc(4). When doing so, ensure
that the large recesses on the sanding disc(4) engage in
the locking pins on the sanding disc holder(9). Then push
down firmly on the sanding disc(4) until it clicks into place.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
uAvoid dust accumulation at the workplace. Dust can
easily ignite.
External Dust Extraction (seefigureD–E)
Clip the dust extraction adapter (10) in over the sanding
disc holders (9). Then place the rubber band (12) of the
dust extraction adapter (10) over the power tool battery (2)
on the handle. Insert the vacuum hose (11) into the extrac-
tion adapter (10). Connect the vacuum hose (11) to a dust
extractor. You will find an overview of how to connect vari-
ous dust extractors at the end of these operating instruc-
tions.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Bosch Power Tools 1 609 92A 66A | (26.01.2021)
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch EasyCurveSander 12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyCurveSander 12 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 12.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info