544330

Bosch D-tect 150 SV Manual

20
Zoom out
Zoom in
Previous page
1/219
Next page
20 | English
1 619 929 J48 | (1.7.11) Bosch Power Tools
Device Information
In the “Device Info” menu, information on the measuring tool
is provided, e.g., about the “Operation Time”.
In the “Restore Settings” menu, you can restore the factory
settings.
Examples for Measuring Results
Note: In the following examples, the audio signal on the meas-
uring tool is switched on.
Depending on the size and depth of the object under the sen-
sor range, it is not always possible to positively determine
whether this object is “live” or voltage-free. In this case, the
symbol will appear in indicator n.
“Live” Wire (see figure C)
A “live”, metal object (e. g. a power cable) is within the sensor
range. The object depth is 1.5 cm. The measuring tool emits
the warning signal for “live” conductors as soon as the power
cable is detected by the sensor.
Steel Bar (see figure D)
A magnetic object (e.g. a steel bar) is within the sensor range.
Further objects are also located to the left and right, outside
of the sensor range. The object depth is 5.5 cm. The measur-
ing tool emits an audio signal.
Copper Pipe (see figure E)
A metal object (e. g. a copper pipe) is within the sensor range.
The object depth is 4 cm. The measuring tool emits an audio
signal.
Plastic or Wooden Object (see figure F)
A non-metal object is within the sensor range. The object is
plastic or wooden, and close to the surface. The measuring
tool emits an audio signal.
Large Surface (see figure G)
A metal, large surface (e. g. a metal plate) is within the sensor
range. The object depth is 2 cm. The measuring tool emits an
audio signal.
Many Unclear Signals (see figures H–I)
When many objects are shown in the standard start display,
the wall probably consists of many hollow spaces. To broadly
block out the hollow spaces, switch to the “Metal ”operating
mode. When there are still too many objects being shown,
carry out several height-offset measurements and mark the
detected objects on the wall. Offset marks are an indication
for hollow spaces, whereas marks on a line indicate an object.
Troubleshooting – Causes and Corrective Measures
?
Error Cause Corrective Measure
Measuring tool cannot be switched on
Batteries empty Replace batteries
Batteries incorrectly in-
serted (wrong polarity)
Check if the batteries are inserted correctly
Measuring tool switched on but does not
react
Take out batteries and reinsert again
Measuring tool too warm or
too cold
Wait until operating temperature range is reached
Display indication: “Slipping Wheel”
Wheel losing contact with
the surface
Press the start button 11 and take care that the
two bottom wheels have contact with the wall
while moving the measuring tool; in case of uneven
walls, position a thin piece of cardboard between
the wheels and the wall
Display indication: “Speeding”
Measuring tool has been
moved to quickly
Press the start button 11 and move measuring tool
slowly over the wall
“Temperature over range”
Wait until operating temperature range is reached
“Temperature under
range”
Wait until operating temperature range is reached
“Strong radio signal
detected”
Measuring tool switches off automatically. If possi-
ble, eliminate the interfering radio waves, e.g.
WLAN, UMTS, radar, transmitter masts or micro-
waves, then switch the measuring tool on again.
OBJ_BUCH-1478-001.book Page 20 Friday, July 1, 2011 8:48 AM
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch D-tect 150 SV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch D-tect 150 SV in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info