544330

Bosch D-tect 150 SV Manual

19
Zoom out
Zoom in
Previous page
1/219
Next page
English | 19
Bosch Power Tools 1 619 929 J48 | (1.7.11)
The summit of the curve is displayed in the small scale above
the operating-mode indication h in the form of a U. The object
depth and the material properties (as far as possible) are dis-
played. The maximum measuring depth is 15 cm.
f Conclusions on the object depth cannot be drawn from
the signal strength.
Changing the Display Modes
Note: Changing the display modes is possible in any operat-
ing mode.
To switch from the standard start display to rule mode, press
and hold selection button 10 or 12.
In the example, rule mode shows the same situation as in
figure D: Three steel bars equally apart. In rule mode, the clear-
ance between the detected object centres can be determined.
The measuring distance covered from the starting point (in
the example 20.1 cm) is displayed under the indication of the
object depth l.
The three objects are displayed as rectangles in the small rule
above the operating-mode indication h.
Note: Both the indication of the object depth l as well as the
material property m refer to the object pictured black in the
sensor.
To return to the standard start display, briefly press selection
button 10 or 12.
Note: Only the display is reset, not the measuring mode!
“Settings” Menu
To access the “Settings” menu, press the setup button 14.
To exit the menu, press the start button 11. The current set-
tings are saved. The standard start display for the measuring
process is activated.
Navigating in the Menu
Press the setup button 14 to scroll down.
Press the selection buttons 10 and 12 to select the values:
– Selection button 10 will select the right-hand or next value.
– Selection button 12 will select the left-hand or previous
value.
Language
In the “Language” menu, you can change the menu-guidance
language. The default setting is “English”.
Cut-off Time
In the “Cut- off time” menu, you can set certain time intervals
after which the measuring tool shall automatically shut off
when no measurements are taken or settings are carried out.
The default setting is “5 min”.
Light Duration
In the “Display illum.” menu, you can set a time interval, dur-
ing which the display 16 shall be illuminated. The default set-
ting is “30 sec”.
Brightness
In the “Brightness” menu, you can set the brightness of the
display backlight. The default setting is “Max”.
Tone Signals
In the “Tone signal” menu, you can limit when the measuring
tool shall give out an audio signal, provided that you have not
switched off the signal with the audio signal button 13.
– The default setting is “Wallobjects”: An audio signal
sounds after each button press, and whenever a wall ob-
ject is under the sensor range. Additionally, a short-beat
warning signal is given for “live” wires.
– With the adjustment “Live wire”, an audio signal sounds
after each button press, as does the warning signal for
“live” wires (short-beat signal) when the measuring tool in-
dicates a power line.
– With the adjustment “Keyclick”, an audio signal only
sounds when pressing a button.
Default Mode
In the “Defaultmode” menu, you can set the default operat-
ing mode that is to be pre-set after switching the measuring
tool on. The operating mode “Concrete Universal” is the de-
fault setting.
“Extended Settings” Menu
To access the “Extended settings” menu, press the setup but-
ton 14 and the On/Off button 15 at the same time when the
measuring tool is switched off.
To exit the menu, press the start button 11. The standard
start display for the measuring process is activated and the
settings are saved.
Navigating in the Menu
Press the setup button 14 to scroll down.
Press the selection buttons 10 and 12 to select the values:
– Selection button 10 will select the right-hand or next value.
– Selection button 12 will select the left-hand or previous
value.
N
S
?
3020 cm10 cm0cmcm
Signal View
Prev. Next
4.0 cm
?
N
S
20 19 18 21 22 23
4030 cm20 cm10 cmcm
Concrete Special
Prev. Next
20.1 cm
5.5 cm
OBJ_BUCH-1478-001.book Page 19 Friday, July 1, 2011 8:48 AM
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch D-tect 150 SV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch D-tect 150 SV in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info