780622
32
Zoom out
Zoom in
Previous page
1/52
Next page
Inspection and maintenance
Condens 7000 WP – 6721841195 (2022/01)
32
9.4.3 Thermal disinfection
To prevent hot water from becoming contaminated by bacteria such as
legionella, we recommend thermal disinfection after long downtimes.
CAUTION
Risk of scalding.
During thermal disinfection, discharging unmixed hot water can cause
serious scalding.
Only use the maximum adjustable hot water temperature for thermal
disinfection.
Inform occupants of the premises of the risk of scalding.
Perform thermal disinfection outside of the normal operating times.
Do not discharge DHW unmixed.
Proper thermal disinfection involves the DHW system including the
draw-off points.
Set the thermal disinfection in the hot water program of the heating
controller (heating controller operating instructions).
Close DHW draw-off points.
Set any DHW circulation pump to continuous operation.
Wait until the maximum temperature is reached.
Open all DHW draw-off points, from the nearest to the one furthest
away, and draw off hot water until hot water at a minimum of 70 °C
has flown from all draw-off points for at least 3 minutes.
Restore the original settings.
10 Inspection and maintenance
WARNING
Risk of explosion
Close the gas valve before working on gas-carrying components.
After completing the work, check the tightness of all gas-carrying
components.
CAUTION
Flue gas poisoning
Check the tightness of all flue gas routing parts once the work is
complete.
CAUTION
Electric shock
Avoid contact with the burner control unit, fan or pump when
measuring and adjusting the boiler. These are 230 V parts.
Switch off the boiler before working on electrical parts.
CAUTION
Malfunctioning safety sensors
The function of the safety sensors in the installation room (such as CO,
CO2, and gas detectors) must be regularly checked.
Check the function of relevant safety sensors during inspection or
maintenance.
You can read about how to perform the check in the instructions for
the safety sensor.
Defects at relevant safety sensors must be rectified immediately.
10.1 Important notices
You will need the following measuring devices and tools:
Pressure gauge with a measurement accuracy of 0.01 mbar.
Flue gas analysis measurement device.
Cleaning brush with plastic bristles.
Only install original spare parts.
Replace all loose gaskets when carrying out the work.
Inspection and maintenance interval
To ensure the wall mounted gas condensing boiler works correctly and
safely, the following intervals must be adhered to:
Inspection: annually,
Maintenance: every 2 years or following a burner runtime of 4000
hours (depending on which occurs first).
The following tasks must be performed when carrying out an inspection
or maintenance:
Table 17 Work to be carried out
10.2 General work
The following work is not described in any further detail in this
document. It must, nevertheless, still be carried out:
Check the general condition of the heating system.
Visual inspection and function check of the heating system.
Check the supply air and flue gas routing for function and safety.
Check all gas and water pipes for signs of corrosion.
Replace any corroded pipes.
Check the pre-charge pressure of the expansion vessel.
Check the concentration of any antifreeze/additives that may be used
in the system fill/top-up water annually.
If necessary, check installed water treatment cartridges
(in the backfeed section) to ensure they are functioning correctly and
for wear.
During commissioning and the annual inspection, check all
regulating, control and safety equipment for correct function and,
where applicable, for correct settings.
Reading out Hours run
The number of Hours run that have elapsed since initial commissioning
is displayed in the menu. The number of Hours run specifies whether:
Components need to be replaced as a preventative measure.
The Maintenance type needs to be modified.
Open the menu Info > Boiler > Hours run.
Read out the number of Hours run.
Check based on the value read out whether components need to be
replaced ( § 10.16.1, p. 36).
Make a note of the value in the maintenance protocol ( § 10.17, p.
38).
Establish the difference between the value most recently read out
and the previous value from the maintenance protocol.
Check the setting Maintenance type based on this difference and
adjust if required ( § 8.2, p. 22).
Inspection Maintenan
ce
General work § 10.2  
Cleaning § 10.3 to § 10.8 -- 
Check
measurements
§ 10.9 to § 10.15  
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Condens GC7000WP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Condens GC7000WP in the language / languages: English as an attachment in your email.

The manual is 15.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Condens GC7000WP

Bosch Condens GC7000WP User Manual - English - 12 pages

Bosch Condens GC7000WP Installation Guide - German - 60 pages

Bosch Condens GC7000WP User Manual - German - 12 pages

Bosch Condens GC7000WP Installation Guide - Dutch - 56 pages

Bosch Condens GC7000WP User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info