780622
24
Zoom out
Zoom in
Previous page
1/52
Next page
Commissioning
Condens 7000 WP – 6721841195 (2022/01)
24
8.6 Measuring of CO2 and CO (full load)
The CO content in the flue gases must be less than 250 ppm (0.025 %
by volume) during combustion without excess air. If the CO content
exceeds 250 ppm, this will be due to pollution of the burner, malfunction
of the burner or recirculation of the flue gases.
Switch off the appliance.
Remove the plug on the test point for flue gas [1].
Fig. 32 Remove the plug on the flue outlet
[1] Test point for flue gas
[2] Test point for air supply
2
2
Make sure that the boiler can release its heat.
Insert the lance of the flue gas analyser 10 cm into the test point.
Operate the appliance.
Open the menu Function check > Burner.
Start the Function check by setting the value to 100%.
Measure the CO content.
Determine and eliminate the cause of the potentially high CO
content.
Make a note of the CO content in the commissioning report ( §
15.7, p. 50).
Measure the CO percentage.
Check the measured value ( table 11, p. 24).
Only modify the CO level if the measurement is outside
the specified range.
Make a note of the measured CO2 slevel in the commissioning
report
§ 15.7, p. 50).
Deactivate Function check.
Remove the flue gas analyser.
Fit the plug on the test point for flue gas.
Setting data
Table 11 Setting data
8.7 Measuring the gas/air ratio (minimum load)
Switch off the appliance.
Make sure the heating system can release its heat.
Open the gas/air ratio test port by turning the adjusting screw
through 2 revolutions (§ 8.3, p. 23).
Set the pressure gauge to “0”.
Connect the pressure gauge to the test port.
Open the menu Function check > Burner.
▶Start Function check by setting the smallest possible value.
Check the measured value ( table 11, p. 24).
Only modify the gas/air ratio if the measurement is outside the
specified range.
The gas/air ratio adjusting screw is underneath the cover.
Make a note of the measured value [Pa] in the commissioning report
( § 15.7, p. 50).
▶Deactivate Function check.
Close with the gas/air ratio test port.
8.8 Reading off the ionisation current
Open the menu Function check > Burner.
▶Start Function check by setting the smallest possible value.
Open the menu Info > Ionisation current.
Reading off the ionisation current.
The ionisation current must be at least 2 A.
If the value is lower, check the gas/air ratio and the igniter.
Make a note of the value that has been read off [A] in the
commissioning report ( § 15.7, p. 50).
▶Deactivate Function check.
Appliance type: Gas type CO2
percentage
Gas/air ratio
[%] [Pa]
GC7000WP 50 Natural gas H
(G20)
9.3 ± 0.3
-5 ± 4
Natural gas L
(G25)
9.1 ± 0.3
Propane L
(G31)
10.0 ± 0.3
0010034264-002
2
1
GC7000WP 65 Natural gas H
(G20)
9.3 ± 0.3
-5 ± 4
Natural gas L
(G25)
9.1 ± 0.3
Propane L
(G31)
10.0 ± 0.3
GC7000WP 85 Natural gas H
(G20)
9.1 ± 0.3
-5 ± 4
Natural gas L
(G25)
9.1 ± 0.3
Propane L
(G31)
10.0 ± 0.3
GC7000WP 100 Natural gas H
(G20)
9.1 ± 0.3
-5 ± 4
Natural gas L
(G25)
9.1 ± 0.3
Propane L
(G31)
10.0 ± 0.3
Appliance type: Gas type CO2
percentage
Gas/air ratio
[%] [Pa]
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Condens GC7000WP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Condens GC7000WP in the language / languages: English as an attachment in your email.

The manual is 15.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Condens GC7000WP

Bosch Condens GC7000WP User Manual - English - 12 pages

Bosch Condens GC7000WP Installation Guide - German - 60 pages

Bosch Condens GC7000WP User Manual - German - 12 pages

Bosch Condens GC7000WP Installation Guide - Dutch - 56 pages

Bosch Condens GC7000WP User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info