632161
14
Zoom out
Zoom in
Previous page
1/84
Next page
EURO • Printed in England • BA F 016 L69 797 • ARM 320 • GB • OSW 11/00
English - 3
F016 L69 797 • 11.00
Electrical Safety
Your machine is double insulated for safety and re-
quires no earth connection. The operating voltage is
230 V AC, 50 Hz. Only use an approved extension
cable. Contact your service agent for details.
It is recommended for increased electrical safety to
use a Residual Current Device (RCD) with a tripping
current of not more than 30 mA. Always check your
RCD every time you use it.
WARNING: For safety, it is essential that the mains
plug 4 attached to the machine is fitted to the power
supply cable 11 as in figure B.
The couplings of connection leads must be protected
against splashes and the coupling sockets on the
leads must be made of rubber or coated with rubber.
Fixing means for the connection leads must be used.
The connection lead must be inspected for signs of
damage at regular intervals and may only be used if
in perfect condition.
If the supply cord is damaged it must be replaced by
a Bosch approved service agent.
Extension cords/leads should only be used if they
comply with H05VV-F or H05RN-F types.
Products sold in GB only: Your mower is fitted with
an approved 13 A (BS 1363/A) electric plug and is
protected by a 13 A fuse (ASTA Approved to
BS 1362).
If the fitted plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fitted in
its place.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted
into a 13 A socket elsewhere.
Insert the handle bottom 8 into the holes pro-
vided and
secure with the screws.
Attach the handle top 3 with the bolts and wing
nuts 12 to the handle bottom 8, as in figure A.
Note: The handle top 3 is height adjustable. Fix han-
dles in desired position I or II.
Attach cable to cable restraint 5 as in figure B ensur-
ing that sufficent cable slack is available.
Snap together both top and bottom half of the grass-
box.
Fitting
Lift the deflector guard 7 and hold up, fit the grass-
box 6.
Removing/Emptying
Lift the deflector guard 7 and hold up. Remove
grassbox 6.
For non grass collection the mower can be used
without the grassbox 6 in position, with the deflector
guard 7 in the down position.
Stop, release switch lever and wait until
the motor stops before adjusting hight.
Your machine has four settings which give the fol-
lowing approximate height of cuts:
I = 24 mm II = 40 mm III = 55 mm IIII = 70 mm
Remove the grassbox to aid adjustment (see Grass-
box).
Lift the mower,
Pull/push the wheel to the front of the mower us-
ing the hand positioned on the wheels.
Raise/lower the wheel.
Allow wheel to locate in desired position as in fig-
ure D.
Make sure that all wheels are set to the same height.
For the first cutting of the season, a high cutting ad-
justment should be selected.
Assembly
Grassbox
Adjusting the Cutting Height
F 016 L69 797.book Seite 3 Dienstag, 21. November 2000 7:52 07
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch ARM 320 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch ARM 320 in the language / languages: All languages as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info