697457
140
Zoom out
Zoom in
Previous page
1/158
Next page
RPS cannot perform remote
programming and control
Both addresses 0144
and 0145 are set to 0
Program the address
0144 to a number from 1
to 15. Program the
address 0145 to 1
Occasionally abnormal
communication in use of
Contact ID/personal
telephone alarm
Extension system is used
in the telephone network
The telephone network
support ADSL as well
Add dial delay in
programming
Connect the system after
the ADSL filter
No response from the keypad
and the alarm siren
(disabled) when an alarm is
triggered by the zone
The zone silent alarm is
enabled
Disable the zone silent
alarm
The AMAX panel cannot send
any reports (programmed to
send reports to receiver)
The transmission format
of the receiver is
programmed to 0 = not
used
Program the
transmission format of
the receiver to 1 or 3
A-LINK cannot be connected
with ITS- DX4020-G
The parameters of ITS-
DX4020-G are not
properly set.
Recommend to set the
parameter ACK TIMEOUT
of ITS-DX4020-G to the
maximum (600) and set
TRANSMIT BUFFER LIFE
TIME to the maximum
(120)
Trouble Fault Inquiry
Fault Description
1 - Accessory Module Failure
Network / IP Module 1 Failure
Condition:
No communication with the DX4020 / ITS-DX4020G if DX4020 / ITS-DX4020G is programmed.
Restore:
Communication with DX4020 / ITS - DX4020G is normal and fault is reset.
Supervise:
1. Report the DX4020 / ITS - DX4020G fault to configured destination on address 124 when
the fault is detected.
2. Slow flash FAULT indicator (refer to Keypad Indicators for the detailed description).
3. When the fault is reset, send the restored report to the configured destinations. The
FAULT indicator is turned off, when there is no other system fault.
Output Expansion Module Failure
Condition:
No communication with DX3010 if DX3010 is programmed.
Restore:
10.2
140 en | Troubleshooting AMAX 2100 / 3000 / 4000
2013.10 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitsysteme GmbH
140


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AMAX 4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AMAX 4000 in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AMAX 4000

Bosch AMAX 4000 User Manual - English - 24 pages

Bosch AMAX 4000 User Manual - English - 36 pages

Bosch AMAX 4000 Quick start guide - English - 38 pages

Bosch AMAX 4000 Installation Guide - German - 170 pages

Bosch AMAX 4000 Quick start guide - German - 34 pages

Bosch AMAX 4000 Installation Guide - Dutch - 166 pages

Bosch AMAX 4000 User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info