Manual Bosch AKE 35 (page 17 of 139) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

1151

Zoom out

Zoom in

1/139

English - 2

17 • F016 L70 362 • TMS • 25.04.06

■ Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

■ Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

■ Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

■ Use the power tool, accessories and tool bits

etc., in accordance with these instructions and

in the manner intended for the particular type of

power tool, taking into account the working

conditions and the work to be performed. Use of

the power tool for operations different from those

intended could result in a hazardous situation.

Service

■ Have your power tool serviced by a qualified re-

pair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

Chain Saw Safety Warnings:

■ Keep all parts of the body away from the saw

chain when the motor is operating. Before you

start the saw, make sure the saw chain is not

contacting anything. A moment of inattention

while operating chain saws may cause entangle-

ment of your clothing or body with the saw chain.

■ Always hold the chain saw with your right hand

on the rear handle and your left hand on the

front handle. Holding the chain saw with a re-

served hand configuration increases the risk of per-

sonal injury and should never be done.

■ Wear safety glasses and hearing protection.

Further protective equipment for head, hand,

legs and feet is recommend. Adequate protective

clothing will reduce personal injury by flying debris

or accidental contact with saw chain.

■ Do not operate a chain saw in a tree. Operation

of a chain saw in a tree, may result in personal in-

jury.

■ Always keep proper footing and operate the

chain saw only when standing on fixed, secure

and level surface. Slippery or unstable surfaces

such as ladders may cause a loss of balance or

control of the chain saw.

■ When cutting a limb that is under tension be

alert for spring back. When the tension in the

wood fibres is released the spring loaded limb may

strike the operator and/or throw the chain saw out

of control.

■ Use extreme caution when cutting brush and

saplings. The slender material may catch the saw

chain and be whipped toward you or pull you off

balance.

■ Carry the chain saw by the front handle with the

saw chain stopped and the guide bar pointing

to the rear. When transporting or storing the

chain saw always fit the guide bar cover. Proper

handling of the chain saw will reduce the likelihood

of accidental contact with the moving saw chain.

■ Follow instructions for lubricating, chain ten-

sioning and changing accessories. Improperly

tensioned or lubricated chain may either break or

increase the chance for kickback.

■ Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing

loss of control.

■ Cut wood only. Don’t use chain saw for pur-

poses not intended – for example – Don’t use

chain saw for cutting plastic, masonry or non-

wood building materials. Use of the chain saw for

operations different then intended could result in a

hazardous situation.

Causes and Operator Prevention of Kickback:

– Kickback may occur when the nose or tip of the

guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut.

– Tip contact in some cases may cause a sudden re-

verse reaction, kicking the guide bar up and back

towards the operator.

– Pinching the saw chain along the top of the guide

bar may push the guide bar rapidly back towards

the operator.

– Either of these reactions may cause you to lose

control of the saw which could result in serious per-

sonal injury. Do not rely exclusively upon the safety

devices built into your saw. As a chain saw user,

you should take several steps to keep your cutting

jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given below:

■ Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both

hands on the saw and position your body and

arm to allow you to resist kickback forces. Kick-

back forces can be controlled by the operator, if

proper precautions are taken. Do not let go of the

chain saw.

■ Do not over reach and do not cut above shoul-

der height. This helps prevent unintended tip con-

tact and enables better control of the chain saw in

unexpected situations.

■ Only use replacement bars and chains speci-

fied by the manufacturer. Incorrect replacement

bars and chains may cause chain breakage and/or

kickback.

■ Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain. De-

creasing the depth gauge height can lead to in-

creased kickback.

F016 L70 362 - GB Seite 2 Freitag, 28. April 2006 10:08 10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AKE 35 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AKE 35

Bosch AKE 35 User Manual - Dutch - 135 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AKE 35 Manual

Product: