697426

Bosch AGS50-2 Manual

15
Zoom out
Zoom in
Previous page
1/28
Next page
Commissioning | 15
6 720 811 270 (2015/04)AGS10-2, AGS10E-2, AGS20-2, AGS50-2
6.2.6 Determining the frost threshold temperature
To determine the degree of frost protection, we recommend checking
the frost protection of the heat transfer fluid when first putting the
system into operation, by means of a frost protection gauge (a
refractometer). This check should be repeated at regular intervals (at
least every two years).
The commonly used instruments for testing motor vehicle engine
coolants are not suitable for this purpose. A suitable device can be
ordered separately.
For system operation with heat transfer medium LS
If the solar system is operated with heat transfer medium LS, the value
must be converted using Tab. 10.
6.2.7 Correcting frost protection
If the minimum frost protection level is not being maintained, more heat
transfer fluid must be added.
▶ Use Tab. 11 to determine the volume of the system, so that you can
calculate the exact amount to be added (which is equal to the amount
which first needs to be drained out).
▶ Use the formula on the right to determine the amount of concentrate
to be added (V
replace
).
Example of heat transfer medium L:
• System volume (V
total
) = 22 l
• Frost protection level (reading taken): – 14 °C
• Equals concentration of ( Tab. 10, page 15): 29 % (C = 29)
•Result: V
replace
= 4.3 l
▶ Drain the calculated amount to be added (V
replace
) and add
concentrate.
6.3 Setting the flow rate
The flow rate is set when the system is cold (30 - 40 °C).
• When the solar pump is speed-controlled, the controller determines
the flow rate based on operating requirements.
• If the controller is not equipped with speed control or if speed control
has been deactivated, the flow rate must be set to a fixed flow rate.
If you wish to set the flow rate:
1. Carry out the preparatory work ( Chapter 6.3.1)
2. Check the flow rate ( Chapter 6.3.2)
3. Set the flow rate ( Chapter 6.3.3)
6.3.1 Carrying out the preparatory work
▶ Rotate ball valves [1] to 0° (check valves ready for operation).
▶ Completely open the flow limiter [2].
▶ On the controller, select mode “Manual ON” ( controller instruction
manual).
Fig. 26
[1] Gravity brake ready for operation
[2] Adjusting screw on the flow limiter, depending on the type
[3] Read-off edge for the flow rate, depending on the type
Value recorded for heat transfer
medium L (concentration)
Corresponds to frost protection
with heat transfer medium LS
– 23 °C (39 %) – 28 °C
– 20 °C (36 %) – 25 °C
– 18 °C (34 %) – 23 °C
– 16 °C (31 %) – 21 °C
– 14 °C (29 %) – 19 °C
– 11 °C (24 %) – 16 °C
– 10 °C (23 %) – 15 °C
– 8 °C (19 %) – 13 °C
– 6 °C (15 %) – 11 °C
– 5 °C (13 %) – 10 °C
– 3 °C (8 %) – 8 °C
Table 10
NOTICE: Frost damage
▶ Every two years, check whether the required frost
protection level (to at least –25 °C) is being
maintained.
System part Fill volume
Collector: see collector instructions (technical data)
1 single-line solar pump station 0.20 l
1 twin-line solar pump station 0.50 l
1 coil in the solar cylinder (see technical guide)
1 m Cu pipe Ø 15 mm 0.13 l
1 m Cu pipe Ø 22 mm 0.31 l
1 m Cu pipe Ø 28 mm 0.53 l
1 m Cu pipe Ø 35 mm 0.86 l
1 m Cu pipe Ø 42 mm 1.26 l
1 m stainless steel corrugated pipe DN16 0.26 l
1 m stainless steel corrugated pipe DN20 0.41 l
1 m stainless steel corrugated pipe DN25 0.61 l
Table 11 Volume of the separate system parts
V
replace
= V
total
x
43 - C
concentration
100 - C
concentration
Table 12 Formula for calculating the amount of fluid to be replaced
0,5
7
6
5
4
3
2
1
L/min
7
6
5
4
1
0,5
3
2
6720801165.18-2.ST
1
20
0
40
60
°C
80
100
120
20
0
40
60
°C
80
100
120
S E
3
2
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AGS50-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AGS50-2 in the language / languages: English as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info